1)  oblique collision
斜角碰撞
1.
The vehicle behaviors of three frontal collision modes, including the full frontal collision,the oblique collision,and the offset frontal collision,were discussed.
讨论了全宽正面碰撞、斜角碰撞和偏置碰撞三种碰撞模式的特点。
2)  skew angle
斜角
1.
The transformation of the pressure distribution and the air bearing force under the collective effect of radial velocity and skew angle was investigated during seeking process.
以负压Pico磁头作为物理模型,模拟了磁头在磁盘半径方向寻轨时,磁头径向速度、斜角值的改变对磁头压强的分布和气膜承载力的影响。
3)  deviation angle
井斜角
1.
Before target-entering into a horizontal well or in the process of drilling horizontal section,to confirm the controlling range of deviation angle and azimuth of hole section is not only an important measure to guarantee target rate and trajectory control accuracy of the horizontal well but also one of the important contents in trajectory supervision of the horizontal well.
在水平井入靶前或水平段钻井过程中,确定待钻井段井斜角和方位角的控制范围是保证水平井中靶和轨迹控制精度的关键,也是水平井井眼轨迹监控的一项重要内容。
2.
Due to the complicated calculation formula and trivial deduction course proposed by predecessor, this article derivated a new calculation formula for circular arc well section deviation angle and positional angle based on increment of coordinate identical equation.
前人提出的圆弧井段井斜角和方位角的计算公式具有计算复杂、推导过程烦琐等缺点,为此以坐标增量恒等式为基础,使用初等方法推导出了一组新的圆弧井段井斜角和方位角的计算公式。
3.
The relationships between the critical density and critical salt content of drilling fluid and hole azimuth and deviation angle in horizontally isotropic and anisotropic formation respectively, are studied.
采用常规三轴压缩 Drucker- Prager破坏准则 ,进行了在水平各向同性地层和水平各向异性地层条件下 ,对保持井壁稳定所需的临界钻井液密度和临界钻井液含盐量与井眼方位角和井斜角之间的关系进行了分析和计算 。
4)  Bevel angle feeding
斜角进刀
5)  oblique cutting
斜角切削
1.
A mathematical model for numerical emulation of cutting forces in drilling using drills with indexable inserts based on oblique cutting theory combined with experimental approach is developed.
采用斜角切削理论和试验相结合的方法建立可转位浅孔钻钻削力数值仿真的数学模型。
2.
Using the general international FEM software ANSYS, the dynamic process of oblique cutting is simulated.
借助于通用有限元软件ANSYS模拟出斜角切削的动态过程,并在此基础上对切削变形进行了研究,提出了一种获得剪切角的新方法。
3.
Basing on Merchant oblique cutting theory, dynamic force model for Ball end milling cutter is presented for avoiding the complicated engineering plasticity theory.
基于Merchant斜角切削理论 ,给出了球头铣刀的动态力学模型 ,以避开复杂的工程塑性理论 ,分析了两种建模方法的互补性 。
6)  bevel
定位斜角
参考词条
补充资料:烧饼·缸爿·斜角儿
烧饼·缸爿·斜角儿
烧饼·缸爿·斜角儿

早餐的点心,最平常普通的有桶炉烘烤的烧饼、缸爿与斜角儿。

烧饼的馅儿根据不同季节可用萝卜丝、女儿葱末、韭菜末,配以生脂油或脂油渣。也可根据顾客不同喜好安排馅儿,春季有虾籽烧饼,还有椒盐烧饼,胡椒烧饼,此外有用食糖或豆沙做成的甜烧饼。每到立夏之日烙饼供不应求,许多烧饼店半夜起就开始加工,掘港的十里长街上做烧饼的木槌声不绝,因为传说立夏节吃了烧饼不疰夏。

到夏日午后,还有做酥儿烧饼的。酥儿烧饼个小、酥重、芝麻多。掘港人吃烧饼,喜欢泡一杯天水茶,或买一碗豆腐脑相佐。

斜角儿的加工比烧饼简单多了。加工者将酵团经搓按压扁拉长,将葱油、细盐抺于中间,再将两边相合,用烧饼槌儿滚过再拉长,将糖粞涂于面上,撒上芝麻,这样成了一条酵面的长带子摊在案板上,加工者执刀斜切,每块成平行四边形,再烘烤而成,斜角儿之名即由此得来。斜角儿价格低、口味香、有韧性,夏季新菜油上市,吃斜角通常蘸菜油,这样吃起来更觉爽口。缸爿,做法和斜角儿差不多,只是中间有肉馅儿,加工者用刀横切,成长方形,涂上糖粞,撒上芝麻贴于桶炉。缸爿这个名取其形状,有点象陶器缸片。传说,明代倭寇入侵掘港时,当地乡勇正集合准备出击。领队的对其中一人说,你去把缸爿拿来分给大家,吃了才有力气杀倭子。倭子奸细听到后连忙溜到倭营报告,说掘港人本领了不得,他们在吃“钢板”,吃了“钢板”就来和我们打仗。倭子头目听了,吓了一跳,这掘港人竟能吃“钢板”,我们岂是他们的对手,连忙撤退。这缸爿之名便一直传至今日。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。