说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 应力分析法
1)  stress analysis method
应力分析法
1.
Modeled the reliability of the controller of self-rescue system for AUV,predicted the failure rate λ_s and mean time between failure MTBF by using part stress analysis method,and finally raised several ways to improve the reliability of system.
针对智能水下机器人自救系统的控制器部分建立了其可靠性数学模型,应用元件应力分析法,预计出了自救系统控制器部分的故障率λs及平均故障间隔时间MTBF,并总结了若干提高系统可靠性的途径。
2.
According to the practical issues encountered in boiler inspection the stress analysis method is applied in analytic error calculation of small end of conical head with half top angle>60°.
针对在锅炉检验中常遇到的实际问题 ,应用应力分析法 ,对半顶角大于 60°锥形封头的小端解析误差进行了计算分析 ,并经解析式验算 ,指出其误差在工程允许范围内。
3.
In the paper, the reliability of a module was predicted with device counting method and device stress analysis method repectively.
该文以一个模块为例,分别用元器件计数法和应力分析法进行可靠性预计,从中比较出两种算法的特点,以便更好的适应设计。
2)  Experiment investigation
实验应力分析法
3)  slip surface stress analysis method
滑面应力分析法
1.
The slip surface stress analysis method and strength reducion method are used to analyze the stability of soil nailing support for foundation pit.
采用滑面应力分析法和强度折减法两种有限元方法对基坑边坡的稳定性进行了研究。
2.
The VISUAL FORTRAN is used in the main part of the finite element reliability analysis program,which can carry out finite element analysis of slope stability based on two methods—one is the strength reduction method and the other is the slip surface stress analysis method.
前处理部分采用的是有限元通用分析软件ANSYS的APDL语言,用其编写的程序模块可方便地用于有限元网格的划分,以得到有限元计算所需的结点坐标信息、单元结点编号信息、约束结点自由度信息等内容;有限元主程序采用的是VISUALFORTRAN语言,它可进行基于强度折减法及基于滑面应力分析法的边坡稳定定值法有限元计算,以求解边坡的安全系数及其对应的滑面位置;亦可进行基于强度折减法及基于滑面应力分析法的边坡稳定有限元可靠度计算,以求解边坡的可靠指标及其对应的滑面位置;后处理部分采用的是MATLAB语言,它可方便灵活地绘制网格图、等值线图、滑面位置图及曲线图等各种图形。
4)  design by stress analysis method
应力分析法设计
5)  stress analysiso
应力分析设计法
6)  electromotive stress analysis method
电测应力分析法
1.
This paper, applying test stress analysis method- electromotive stress analysis method, has made experimental research into the results of shape optimization of transition curve of the shaft of viable section, after the theoretical analysis on shape optimization of the axial symmetry body.
本文在分析了轴对称体形状优化理论的基础上,采用试验应力分析方法一电测应力分析法,对变截面轴过渡曲线形状优化结果进行了实验研究。
补充资料:容量分析法(见化学分析法)


容量分析法(见化学分析法)


容t分析法见化学分析法
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条