说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 组件约束
1)  component constraint
组件约束
1.
Aiming at the problem that there exists very complicated and a large amount of component constraints,an algorithm of component constraint detection based on proposition logic was proposed,in which the proposition in daily diction was transformed into the formal proposition of mathematical logic via the process of proposition symbolization,i.
针对组件约束数量大、复杂度高的问题,提出了一种基于命题逻辑的组件约束检测算法。
2.
The method describing characteristics with vector was provided,and component constraints were defined by product characteristic vector.
文章在产品特征可量化的条件下,建立了产品配置模型,给出了特征的向量表示方法,并根据产品特征向量,定义组件约束
2)  component migration constrains
组件迁移约束
3)  the constraints of tes-composing
组卷约束条件
4)  constraints
约束条件
1.
Application of various constraints in videogrammetry for the profilement of gossamer inflatable spacecraft antenna;
多约束条件在薄膜充气天线面形测量中的应用
2.
The application of constraints of scaler to flat panel displayer;
平板显示器中定标器的时序约束条件
3.
Methods to Deal with Constraints in Overload Control Systems of Winged Missile;
飞航导弹过载控制系统中约束条件的处理方法
5)  constraint condition
约束条件
1.
A analysis on structure and constraint condition of the management models of water environment;
水环境管理模型的结构与约束条件分析
2.
A study on axiomatic designing method under constraint conditions;
约束条件下公理化设计方法研究
3.
Analyses on the influence of vibration modal tests under different constraint conditions
不同约束条件下的变速器箱体振动模态试验分析
6)  Constrained Condition
约束条件
1.
The hybridize genetic and non-smooth algorithm of min-max problem under limited and constrained conditions
带界约束条件min-max问题的混合遗传非光滑算法
2.
Based on the dynamic property of framework, a dynamic optimized calculation of multistoriedframewouk is made with the span of framework and sit f fness of beams and columns as design variable, andwith stress,displacement, frequency and size constraints as constrained conditions.
在考虑框架动力特性的基础上,将框架跨度与梁、柱刚度作为设计变量,且约束条件全面考虑了应力、位移、频率和尺寸约束。
3.
This essay presents the problems and all the constrained conditions that should be taken into consideration when arranging courses.
本文描述了排课问题及在设计排课系统时应考虑的各种约束条件,在分析其它排课算法的同时结合孝感学院实际情况,提出了一种基于优先级的自动排课算法,并以该算法设计了一个排课系统。
补充资料:“十”形吹洗组件
分子式:
CAS号:

性质:一种包括三个阀门和一根进气管接头的吹气集管结构。安装在钢瓶和减压器之间。三个阀门中一个是减压器隔离阀,一个是高压旁路阀和一个吹洗气体进口阀。在各部分之间交叉管道的内部通路呈“十”形。316不锈钢焊接结构,高纯无填料膜片阀,在组装前采用超声波洁净处理,在100级洁净室中组装和包装。在更换钢瓶时可消除污染,防止有毒气体外漏以及由于空气中水分进入系统而导致的腐蚀作用。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条