1) semi-integral abutment
半整体式桥台
2) PIAB
半整体式桥台桥梁
3) integral abutment
整体式桥台
1.
Dynamic field-test of integral abutment bridge;
整体式桥台桥梁的动力试验研究
2.
Passive earth pressure behind abutment of integral abutment bridges;
整体式桥台桥梁的台后被动土压力研究
3.
Research on the loaded property of integral abutment bridges with flexible piles;
桩基础的整体式桥台桥梁受力性能研究
4) Integral Abutment Bridges
整体式桥台桥梁
1.
Research on Symplified Calculating Model and Loaded Behavior of Integral Abutment Bridges;
整体式桥台桥梁的简化计算模型与受力性能研究
2.
The three-dimensional framework simplified model of the integral abutment bridges is put forward.
提出了整体式桥台桥梁在成桥阶段计算的三维框架简化模型;然后在ANSYS基础上进行二次开发,编制了计算桩基的等代桩长和台后土压力合力的专用分析程序IABS。
5) integral abutment slab bridge with skew angle
整体式桥台斜板桥
1.
Study on loaded property of integral abutment slab bridge with skew angle under temperature load;
温度荷载下整体式桥台斜板桥的受力性能研究
6) New type semi-integral abutment bridge
新型半整体式无缝桥
1.
New type semi-integral abutment bridge cancels expansion joints (including the expansion joints between end beam and abutment), and shifts away the beam thermal movements to the end of the run-on slab, which are absorbed by soil body of definite length range behind the abutment.
新型半整体式无缝桥取消了全桥伸缩缝(包括梁端和桥台之间的伸缩缝),将主梁、桥台和搭板紧密相连,采用斜置搭板,将梁体变形延至搭板末端,通过台后一定长度范围的土体来吸纳桥梁的伸缩变形。
补充资料：整体锻造式高压容器
分子式：
CAS号：
性质：这是用整体锻造炮筒的技术来制造的高压容器，筒体与法兰可整锻而出或用螺纹连接。锻造容器的质量较好，特别适合于焊接性能较差的高强钢所制造的超高压容器。锻造式高压容器一般直径为φ300～φ800，长度不超过12m。在锻造的筒节上也可采用焊接的方法将筒节与筒节、筒节与端部法兰或底部连接起来而组成的容器为锻焊式容器。
CAS号：
性质：这是用整体锻造炮筒的技术来制造的高压容器，筒体与法兰可整锻而出或用螺纹连接。锻造容器的质量较好，特别适合于焊接性能较差的高强钢所制造的超高压容器。锻造式高压容器一般直径为φ300～φ800，长度不超过12m。在锻造的筒节上也可采用焊接的方法将筒节与筒节、筒节与端部法兰或底部连接起来而组成的容器为锻焊式容器。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条