说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 二氧化碳/最优压力
1)  carbon dioxide/optimum pressure
二氧化碳/最优压力
2)  CO 2 pressure
二氧化碳压力
3)  carbon dioxide partial pressure
二氧化碳分压力
4)  the partial pressure of carbon dioxide gap(Pg-aCO2)
局部二氧化碳压力差
1.
Hemodynamics, artery blood lactate concentration and the partial pressure of carbon dioxide gap(Pg-aCO2), which is difference betweenPgCO2 and PaCO2, were observed before and after fluid resuscitation.
观察复苏前、后血流动力学指标、动脉乳酸浓度(ABL)和局部二氧化碳压力差(Pg-aCO2),即胃粘膜和动脉血二氧化碳压力差。
5)  CO2 at supercritical pressures
超临界压力二氧化碳
1.
Convection heat transfer of CO2 at supercritical pressures in a vertical tube at low Re was investigated experimentally and numerically.
本文对竖直圆管中超临界压力二氧化碳在低雷诺数条件下的对流换热进行了实验研究和数值模拟。
6)  CO2 compressor
二氧化碳压缩机
1.
Briefly presents the damage of CO2 compressor during its startup due to too high shaft direction thrust,analyses reasons for the damage from the aspect of process changes.
简述在开车过程中二氧化碳压缩机轴向推力造成压缩机损坏情况,从工艺变化方面分析其损坏原因,采取相应改进措施和对策后,确保了压缩机组安全稳定运行。
2.
The main reason for the shutdown of urea process system is the trip of high pressure ammonia pump and CO2 compressor.
针对尿素工艺系统故障停车的主要原因为高压氨泵和二氧化碳压缩机跳车造成的,结合生产实际,提出工艺改造方案,有效控制了系统停车。
3.
The operation of CO2 compressor instrument system was adversely affected by the factors, such as unreasonable type selection of some instruments, poor operating quality, and the instrument approaching the end of service life.
二氧化碳压缩机仪表系统的某些仪表因选型不合理,运行品质差,寿命到期等原因,影响了整个仪表系统的运行状况。
补充资料:镁合金压力铸造的优缺点
镁合金压力铸造的优点有:
    高的生产率;
    高精度;
    好的表面质量;
    精细的铸件晶粒;
    可压铸薄壁和复杂结构的产品。
    镁合金压铸和铝合金压铸相比:
    生产率高50%;
    可使用钢模,延长服务寿命;
    更低的潜热,节省能量;
    好的机加工性;
    模具成本节省50%;
    熔体具有更高的流动性。
    镁合金压力铸造也有一些不利的方面,例如:
    由于极高的液体填充速度和凝固速度,易产生卷入性气孔;
    铸件不能太厚,壁厚只能局限于一定的尺寸;
    便宜的压铸合金,有限的机械性能;
    有限的可使用压铸合金种类;
    由于铸件晶粒尺寸细小,抗蠕变能力较差;
    抗蠕变的Mg-Al-RE镁合金的铸造性较差,而且昂贵;
    不能进行热处理;
    不适合焊接。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条