1) radius of rolling circle
滚圆半径
2) rolling radius
滚动半径
1.
Test and Research of Automobile Tyre Rolling Radius;
汽车轮胎滚动半径试验研究
2.
An dynamical model was developed in this paper for dynamic estimation of the longitudinal stiffness and rolling radius of the tires.
通过建立轮胎动力模型,利用基于模式搜索的最小二乘法对轮胎的纵向刚度和滚动半径两个参数进行了动态估计。
3.
This paper introduced the experiment principle and methods of the tire rolling radius measurement, through the road experiment to JEDA car .
介绍了轮胎滚动半径测量的试验原理和试验方法,通过对捷达轿车的道路试验,得出了轮胎滚动半径与轮胎气压、车速和载荷之间的关系。
3) roller radius
滚子半径
1.
And then gets the minimal radius of curvature of the theoretic contour,finally the basic size of the cam can be determined based on the relationship of the roller radius and the working contour,and requirement of the intensity.
本文根据基圆半径与压力角的关系式,应用计算机求出满足许用压力角的最小基圆半径,然后再求出的理论轮廓的最小曲率半径,并根据滚子半径与工作轮廓的关系以及强度要求,最终确定凸轮机构的基本尺寸。
2.
This paper takes account of the several factors including the contour curve of cam,the accuracy of motion, structure size and the time of normal work of cam mechanism by discussing the relationship between the roller radius and contour curve ,the touch-stress between the roller and cam, the thickness of lubricant film.
以凸轮机构的凸轮轮廓曲线、运动的准确性以及结构尺寸和寿命为考虑因素,讨论了凸轮机构从动件滚子的半径与轮廓曲线、凸轮高副的接触应力以及润滑油膜厚度等的关系,提出了滚子半径的选择原则。
4) rolling sphere radius
滚球半径
5) fillet radius
圆角半径
1.
The optimization of drawing technique was researched,and the influence of different blank holder force and minimum die fillet radius on stamping forming was studied as well.
对该零件成形工艺进行了优化,研究了不同的压边力、最小模具圆角半径对冲压成形的影响,通过对模拟结果的分析得出了空调前板的最优化成形方案。
2.
It is shown that,the smaller the fillet radius of the tip is,the better the effect of drag reduction is.
指出:沟槽尖峰处的圆角半径越小其减阻效果越好,沟槽斜面中下部的壁面应力随着圆角半径的减小而降低,但尖峰处的局部壁面应力会随之增大;来流速度对沟槽减阻率的影响很大,对于一种尺度的V型沟槽,存在着一个具有较好减阻效果的来流速度范围,而沟槽面在沿来流方向上的布置位置对减阻效果的影响非常小;沟槽尺度对减阻效果很剧烈;沟槽尖峰处生成的二次涡是产生减阻效果的根本原因,二次涡的强弱与沟槽减阻率的大小紧密相关。
3.
Analyzed the effect of drawing die fillet radius to drawing process, based on theory analysis and production practice, put forward a better simple calculation formula fillet radius, and carried on examples of calculation.
分析了连续拉伸模圆角半径变化对拉伸工艺影响,在理论分析和生产实践基础上提出了一种较好的简便计算凸、凹模圆角半径公式,并进行实例应用计算。
6) radius
[英]['reɪdiəs] [美]['redɪəs]
圆角半径
1.
And on the basis of analyzing the geometry characteristics of the side rail, the corners whose radius deteriorates the formability are modified.
重点对高强度钢纵梁内板的成形性进行了分析,并且在详细分析零件几何特点的基础上,对此模型的圆角半径进行了修改,修改后零件的成形性得到了显著提高。
2.
Effects of Spoke Transition Radius on the Service Stress Concentration of Mg Wheel;
对具有不同过渡圆角半径的轮毂在相同状况下进行有限元服役应力比较分析。
补充资料：滚圆
非常圆：腰身～的母牛丨两只眼睛睁得～～的。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条