1) threshold
门槛性
2) threshold
门槛
1.
Threshold of Global Existence for a Class of Nonlinear SchrSdinger Equations with a Harmonic Potential in R~N;
一类带调和势的非线性Schrdinger方程在R~N中的整体解存在的门槛
2.
It indicates that the key to increase service life of component lies in shortening final crack length ofmicro-short-crack expansion and increasing physics-short-crack threshold demension.
建立了疲劳寿命估算模式,阐述了疲劳寿命的影响因素,指出提高构件使用寿命的关键在于缩短微观短裂纹扩展的终止裂纹长度,增大物理短裂纹扩展的门槛裂纹尺寸。
3.
The results show that there exists a relevant stress threshold for each of the four stresses so that the ratcheting deformation happens and its SR strain increases or decreases in a line like law with the stress as it gets over or below its threshold.
在大量单轴棘轮实验基础上 ,研究了均值、幅值、峰值和谷值应力对 30 4不锈钢的饱和棘轮应变的影响规律 ,首次提出了棘轮应力σr和棘轮门槛值σrth 的概念 ,建立了基于单参数控制的、用于饱和棘轮应变预测的 SRM饱和棘轮本构模型和用于独立循环应力工况下棘轮应变演化预测的 REM棘轮演化模型 ,并由此发展了全面描述任意循环应力工况下棘轮应变演化规律的 URM棘轮演化统一模型。
3) threshold
门槛值
1.
An Investigation on the Relation between the Fatigue Crack Propagation Threshold and Grain Size The Application of the Dislocation Theory;
疲劳裂纹扩展门槛值与晶粒尺寸关系的研究—位错理论的应用
2.
In contrast with the threshold of fatigue cracks,a series of regulation of expanding of fatigue small cracks has been deduced.
采用对比分析方法,从疲劳裂纹的门槛值角度出发,归纳总结了疲劳裂纹的扩展规律。
3.
Near-threshold fatigue crack propagation tests were conducted under combined torsion and tension on a circumferentially pre-cracked round bar of an austenite stainless steel.
研究了带环状预裂纹的奥氏体不锈钢圆棒试样在循环扭转／拉伸复合载荷下,门槛值附近的疲劳裂纹扩展行为,分析了复合加载时不同载荷比对裂纹扩展的影响,对裂纹扩展的初始阶段进行了详细研究,用应力强度因子表征了裂纹扩展开始的门槛值,提出了椭圆方程表达的疲劳裂纹扩展开始的门槛值模型,该方程可在裂纹尖端位移准则的基础上导出,疲劳裂纹扩展停止的门槛值条件也可用椭圆方程表达。
4) project threshold
准入门槛
1.
Based on characteristic of clean production, the feasibility of application of clean production to establishment of project threshold in regional EIA was analysed, with a specific case in a high- tech zone.
根据区域清洁生产特点,结合佛山禅城高新技术开发区环境影响评价过程,探讨开发区层面上实施清洁生产战略在项目准入门槛制定中的可行性,并进行实例应用研究。
5) threshold value
门槛值
1.
Influence of stress ratio R on threshold value △K_(th) of fatigue crack propagation for welded joints of 09CuPCrNi steel;
应力比R对09CuPCrNi钢焊接接头疲劳裂纹扩展门槛值△K_(th)的影响
2.
The results show that the threshold value △Kth of steel with 1.
８％Ｓｉ钢的门槛值△Ｋｔｈ较 ０。
3.
A new method of determinning the threshold value △Kth on a new typeAMSLER fatigue test system by computer control is given.
阐述了用新型AMSLER高频疲劳试验机，结合计算机控制测定材料门槛值△Kth的新方法。
6) fatigue threshold
疲劳门槛
1.
The effect of Mode Ⅲ overload with different parameters on Mode Ⅰ fatigue threshold was investigated for Ouenching-Tempering 40Cr steel in the near-threshold region.
研究了不同参数的Ⅲ型过载对近门槛区调质 40Cr钢Ⅰ型疲劳门槛的影响。
2.
The effect of single overload on ModeⅠfatigue threshold was studied for 40Cr steel with different treating conditions in the near threshold region.
研究了近门槛区单周过载对 40Cr钢热处理组织Ⅰ型疲劳门槛的影响。
3.
It was in-dicated that whether fatigue threshold as a design param-eter depended mainly on fatigue design philosophy, fa-tigue load spectrum and non--destructive inspection tech-nique.
介绍了疲劳设计准则的基本类型,说明了疲劳门槛的意义及其在疲劳设计中的作用,指出疲劳设计准则、疲劳载荷谱及无损检测技术是决定疲劳门槛能否作为疲劳设计参数的三个主要因素。
参考词条
补充资料：连续性与非连续性(见间断性与不间断性)
连续性与非连续性(见间断性与不间断性)
continuity and discontinuity
11an父ux泊g四f“山。麻以角g、.连续性与非连续性(c。nt，n琳t:nuity一)_见间断性与不间断性。and diseo红ti-
说明：补充资料仅用于学习参考，请勿用于其它任何用途。