轮缘偏磨,flange wear,在线英语词典,英文翻译,专业英语

1) flange wear

轮缘偏磨

This paper discusses the problem of flange wear of SS_(7A)、SS_(7C) locomotive.

针对SS7A、SS7C机车在运用中出现轮缘偏磨较为严重,使其使用寿命大大降低这一技术难题,运用VPD技术CAE对SS7A机车进行了轮缘偏磨多因素分析研究,通过分析找出了影响因素关键所在,继之根据影响因素的大小,制定了实施措施。

2) wheel rim

轮缘

A way of calculating the overall heat transfer coefficient of wheel rims of large capacity steam turbines is being suggested.

提出了大功率汽轮机叶轮轮缘总传热系数的计算方法。

These four aspects are: the foreworn and frature of the wheel rim, tread foreworn bedded d ecrustation, regional crush and subside and early brittle fracture of the wheel rim.

为了有效地提高行走车轮的工作寿命 ,使其接近或达到设计周期 ,笔者从车轮损坏的形式、部位即轮缘磨损断裂、踏面磨损层状脱皮和局部压碎凹陷、轮缘早期脆性断裂四个方面进行了分析 ,找出了之所以产生磨损和断裂的原因 ,并提出了延长车轮工作寿命的对策。

3) wheel flange

轮缘

Discussion on the wheel flange thickness measuring basis for meter-gage locomotives;

对米轨机车轮缘厚度测量基准的探讨

This system can automatically detect such important parameters as wheel flange wear, tread wear and fretting, and etc to increase the level of detecting automation and maintenance efficiency of locomotive wheel sets.

针对铁路机车轮对检修的要求 ,研制了机车轮对综合参数自动检测系统 ,该系统能完成对轮缘磨耗、踏面磨耗、踏面擦伤等重要参数的自动测量 ,从而提高了机车轮对检测的自动化程度及轮对检修作业的效

In view of the abnormal wear of wheel flange appeared on 206KP type quasi high speed bogies,the causes to the wear are analyzed from the wheel diameter difference,curve radius,tread contour,assembling error and wear indexes.

针对 2 0 6 KP型准高速转向架出现的轮缘异常磨耗 ,从轮径差、曲线半径、踏面形状、组装误差以及磨耗指数等方面分析产生磨耗的原因 ,并提出改进措

4) wheel flange wear

轮缘磨耗

5) flange clearance

轮缘间隙

The flange clearance leakage flow and the pressure of vane surface as well as the streamline distribution laws in the case of different cam industrial operation conditions are obtained via the numerical simulation of leakage flow of different flange clearances of the bulb tubular turbine under the different conditions of industrial operation.

通过对灯泡贯流式水轮机在不同工况、不同轮缘间隙的泄漏流动进行数值模拟,得到了不同协联工况下轮缘间隙泄漏流动和叶片表面的压力及流线的分布规律。

Based on N-S equation,k-ε turbulence model,unstructured grid and clumpy gridding technology,the method of calculating unitedly the guide vane and runner was introduced,flow on flange clearance at 0,0.

本文基于N-S方程和k-ε湍流模型、非结构化网格和多块网格技术,采用导叶和转轮部分联合计算的方法,在不同工况下,对贯流式水轮机模型转轮轮缘间隙在0、0。

The paper expounds pressure distribution of the runner blade which is influenced under the leak flow in the flange clearance region.

基于 Navier-Stokes 方程和标准 k-ε紊流模型,数值模拟轴流转桨式水轮机在含轮缘间隙时转轮内部的流场分布情况。

6) flexible rim

柔性轮缘

The analysis method and model of the dynamic contact stress of double circular arc gears were established based on flexible rims and ANSYS/LS-DYNA software,and the factors affecting the dynamic model establishment was analyzed.

基于柔性轮缘和ANSYS/LS-DYNA建立了双圆弧齿轮动态接触应力的分析方法和模型,分析了影响动态模型建立的因素。

参考词条

轮缘冲角车轮轮缘轮缘系数薄轮缘轮缘踏面轮缘厚度齿轮轮缘齿轮缘飞轮轮缘活动轮缘可卸轮缘轮缘驱动皮带轮缘传质与动力学多比特纠缠态

补充资料：大羯磨轮

【大羯磨轮】

　（术语）连续十字金刚而作大圆轮也。瑜只经曰：“当观吽一字成大羯磨轮。”

说明：补充资料仅用于学习参考，请勿用于其它任何用途。

首页 \| 翻译 \| 影视 \| 论坛 \| 索引轮缘润滑轮缘封严橡胶轮缘叶轮轮缘轮缘力轮缘槽

1) flange wear 轮缘偏磨 1. This paper discusses the problem of flange wear of SS_(7A)、SS_(7C) locomotive. 针对SS7A、SS7C机车在运用中出现轮缘偏磨较为严重,使其使用寿命大大降低这一技术难题,运用VPD技术CAE对SS7A机车进行了轮缘偏磨多因素分析研究,通过分析找出了影响因素关键所在,继之根据影响因素的大小,制定了实施措施。 2) wheel rim 轮缘 1. A way of calculating the overall heat transfer coefficient of wheel rims of large capacity steam turbines is being suggested. 提出了大功率汽轮机叶轮轮缘总传热系数的计算方法。 2. These four aspects are: the foreworn and frature of the wheel rim, tread foreworn bedded d ecrustation, regional crush and subside and early brittle fracture of the wheel rim. 为了有效地提高行走车轮的工作寿命 ,使其接近或达到设计周期 ,笔者从车轮损坏的形式、部位即轮缘磨损断裂、踏面磨损层状脱皮和局部压碎凹陷、轮缘早期脆性断裂四个方面进行了分析 ,找出了之所以产生磨损和断裂的原因 ,并提出了延长车轮工作寿命的对策。 3) wheel flange 轮缘 1. Discussion on the wheel flange thickness measuring basis for meter-gage locomotives; 对米轨机车轮缘厚度测量基准的探讨 2. This system can automatically detect such important parameters as wheel flange wear, tread wear and fretting, and etc to increase the level of detecting automation and maintenance efficiency of locomotive wheel sets. 针对铁路机车轮对检修的要求 ,研制了机车轮对综合参数自动检测系统 ,该系统能完成对轮缘磨耗、踏面磨耗、踏面擦伤等重要参数的自动测量 ,从而提高了机车轮对检测的自动化程度及轮对检修作业的效 3. In view of the abnormal wear of wheel flange appeared on 206KP type quasi high speed bogies,the causes to the wear are analyzed from the wheel diameter difference,curve radius,tread contour,assembling error and wear indexes. 针对 2 0 6 KP型准高速转向架出现的轮缘异常磨耗 ,从轮径差、曲线半径、踏面形状、组装误差以及磨耗指数等方面分析产生磨耗的原因 ,并提出改进措 4) wheel flange wear 轮缘磨耗 5) flange clearance 轮缘间隙 1. The flange clearance leakage flow and the pressure of vane surface as well as the streamline distribution laws in the case of different cam industrial operation conditions are obtained via the numerical simulation of leakage flow of different flange clearances of the bulb tubular turbine under the different conditions of industrial operation. 通过对灯泡贯流式水轮机在不同工况、不同轮缘间隙的泄漏流动进行数值模拟,得到了不同协联工况下轮缘间隙泄漏流动和叶片表面的压力及流线的分布规律。 2. Based on N-S equation,k-ε turbulence model,unstructured grid and clumpy gridding technology,the method of calculating unitedly the guide vane and runner was introduced,flow on flange clearance at 0,0. 本文基于N-S方程和k-ε湍流模型、非结构化网格和多块网格技术,采用导叶和转轮部分联合计算的方法,在不同工况下,对贯流式水轮机模型转轮轮缘间隙在0、0。 3. The paper expounds pressure distribution of the runner blade which is influenced under the leak flow in the flange clearance region. 基于 Navier-Stokes 方程和标准 k-ε紊流模型,数值模拟轴流转桨式水轮机在含轮缘间隙时转轮内部的流场分布情况。 6) flexible rim 柔性轮缘 1. The analysis method and model of the dynamic contact stress of double circular arc gears were established based on flexible rims and ANSYS/LS-DYNA software,and the factors affecting the dynamic model establishment was analyzed. 基于柔性轮缘和ANSYS/LS-DYNA建立了双圆弧齿轮动态接触应力的分析方法和模型,分析了影响动态模型建立的因素。参考词条轮缘冲角车轮轮缘轮缘系数薄轮缘轮缘踏面轮缘厚度齿轮轮缘齿轮缘飞轮轮缘活动轮缘可卸轮缘轮缘驱动皮带轮缘传质与动力学多比特纠缠态补充资料：大羯磨轮【大羯磨轮】　（术语）连续十字金刚而作大圆轮也。瑜只经曰：“当观吽一字成大羯磨轮。” 说明：补充资料仅用于学习参考，请勿用于其它任何用途。
©2008 dictall.com