说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 虚拟操作设备
1)  virtual operating device
虚拟操作设备
1.
By introducing the concepts of virtual operating device and its running mechanisms,controlled Petri-net descriptions of the above three control models are given based on system confirm-serv.
通过引入虚拟操作设备及其运行机制,采用系统确认服务模型给出了包含直接控制、监督控制及分享控制3种模式的系统受控Petri网模型,为遥操作机器人系统人机合作问题的解决提供了有意义的参考方案。
2)  Virtual manipulation
虚拟操作
1.
Virtual manipulation and virtual machining technology of machining equipment under virtual environment are the important research topics of virtual manufacturing.
虚拟环境下加工设备虚拟操作和虚拟加工是虚拟制造的一个重要研究内容。
2.
The system drives the virtual hands to accomplish the training tasks in the virtual manipulation environment by tracking the trainee\'s hand positions and gestures based on Motion Tracking Device and acquiring the data of the trainee\'s hand joints based on Data Glove in real world.
采用基于Vega和Creator的虚拟现实仿真机制和人机交互设备,构建某型工程车训练仿真系统虚拟操作训练环境。
3)  virtual operation
虚拟操作
1.
The method offered in this paper is applied and verified in a certain missile virtual operation training system.
在完成基于OKDN资源、虚拟样机、操作、约束条件、误操作与操作延迟判断和处理建模的基础上,提出了基于OKDN虚拟操作训练过程建模规则。
4)  Virtual equipment
虚拟设备
1.
Design and implementation of virtual equipment and simulation system based on Java;
基于Java的虚拟设备仿真系统的设计与实现
2.
The research on virtual equipment and simulating system for microwave technique experiment is presented in this paper The necessity for virtual equipment and the simulating system is discussed The modeling of mathematics and basic means of achievement for virtual experiment are introduce
本文作者第一次提出了用于微波技术实验教学的计算机虚拟设备和实验仿真系统的研究方法 ,讨论了实现微波技术实验教学虚拟设备和仿真系统的必要性 ,介绍了微波技术实验虚拟现实的数学模型的建立和基本的实现手
3.
On virtual beer bottling production line is studied, on the large-scale virtual equipment and bottling production line is researched from the aspects of construction process and mold.
以虚拟啤酒灌装生产线为研究对象,对大型虚拟设备及灌装生产线的构建过程、模式方法进行了探讨和研究。
5)  virtual device
虚拟设备
1.
Approach for modeling virtual device library in VLAB;
VLAB中虚拟设备库建模方法的研究
2.
Application and implementation of Linux virtual device in EPON system;
Linux虚拟设备在EPON中的应用与实现
3.
Meanwhile, introduce concept ofvirtual device logic to realize macro-decoupling of logic conceptand micro-decoupling of soft module, extensibility and stabilityof software are highly increased.
同时,引入虚拟设备逻辑概念,实现宏观的逻辑概念解耦与微观的软件模块解耦,极大地提高了软件的易扩展性和稳定性。
6)  Virtual hand operating
虚拟手操作
补充资料:锻压设备通用操作规程
一、
操作者必须经过考试合格,并持有本设备的《设备操作证》方可操作本设备。
二、 工作前认真做到:
1、仔细阅读交班记录,了解上一班工作情况。
2、检查设备及工作场地是否清扫、擦试干净;设备床身、工作台面、导轨以及其它主要滑动面上不得有障碍物、杂质和新的拉、研、碰伤。如有上述情况必须清除,并擦试干净设备;出现新的拉、研、碰伤应请设备员或班组长一起查看,并作好记录。
3、检查各操作机构的手柄、阀、杆、以及各主要零、部件(滑块、锤头、刀架等)应放在说明书规定的非工作位置上。
1、检查各安全防护装置(防护罩、限位开关、限位档铁、电气接地、保险装置等)应齐全完好、安装正确可靠;配电箱(盒)、油箱(池)、变速箱的门盖应关闭。
2、检查润滑部位(油池、油箱、油杯导轨以及其他滑动面)油量应充足,并按润滑批示图表加油。
3、检查各主要零、部件以及紧固件有无异常松动现象。
4、打开气(汽)路阀门,检查管道阀门及其它装置应完好无泄漏,气(汽)、压应符合规定,并放掉管中的积水。
5、进行空运转试车,起动要寸动,检查各操作装置、安全保险装置(制动、换向、联锁、限位、保险等)各指示装置(指示仪表、指示灯等)工作应灵敏、准确可靠;各部位动作应协调;供油应正常,润滑应良好;机床运转无异常声音、振动、温升、气味、烟雾等现象。确认一切正常,方可开始工作。凡连班工作的设备,交班人员根据上述(8条)规定共同检查进行交接班;凡隔班接班的设备,发现上一班有严重违犯操作规程现象,应请设备员或班组长一直查看,并记录在案,否则发生设备问题以本班违犯操作规程论。设备经过调整或检修后,操作者也必须按照上述(8条)要求和步骤对设备进行检查,确认一切无误,方可开始工作。
三、 工作中认真做到:
1、坚守工作岗位,精心操作设备,不做与工作无关的事。因事离开设备时要停机,并关闭电、气(汽)源。
2、按说明书规定的技术规范使用设备,不得超规范、超负荷使用设备。
3、密切注意设备各部位润滑情况,按润滑指示图表规定进行班中加油,保证设备各部位润滑良好。
4、密切注意设备各部位工作情况,如有不正常声音、振动、温升、异味、烟雾、动作不协调,失灵等现象,应立即停机检查,排除后再继续工作。
5、调速、更换模具、刀具或擦试,检修设备时,要事先停机,关闭电、气(汽)源。
6、在工作时,不得擅自拆卸安全防护装置和打开配电箱(盒)、油池(箱)、变速箱的门盖进行工作。
7、设备发生事故必须立即停机,保护好现场,报告有关部门分析处理,做到三不放过后,方可使用设备。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条