1) shake bell recognition
振铃识别
2) distinctive ringing
区别振铃
3) vibration recognition
振动识别
1.
A model of multi-parameter comprehensive recognition system based on D-S evidential theory and neural networks was proposed with respect to the facts that it was difficult to distinguish different faults from one symptom domain during the compound vibration recognition process of a drive machine.
在D -S证据理论的基础上 ,针对动力机械复合振动识别中在同一征兆域中很难区分多种振动故障的实际状况 ,研究利用其他征兆域的识别信息 ,进行全局信息融合 ,从而达到较为准确的振动故障定位 ;系统地论述了基于证据理论和神经网络的多参数体系识别的数据融合方法 ,在该方法中采用证据理论的组合规则进行局部和全局信息融合 ,结果表明D -S证据理论能有效地识别动力机械复合振动特征 ;给出了识别实
4) vibration resource identification
振源识别
1.
Two methods respectively based on the law of amplitude fading and characteristic parameters of angle domain are put forward to solve the problems of vibration resource identification of multi bearings installed on the same axis under state of incomplete rotation.
多个低速重载轴承同轴安装时,产生的故障振动脉冲会出现混叠现象,分别提出了利用振幅衰减原理和角域特征参量2种方法,解决了多轴承同轴不完全旋转状态下的振源识别问题,为脉冲信号的振源正确分离为低速重载轴承故障诊断方法研究奠定了基础。
5) Chatter Recognition
颤振识别
1.
Chatter Recognition System of NC Machining Based on Analysis on Audio Signal
基于切削噪声测试的数控加工颤振识别系统
6) ringing
[英]['rɪŋɪŋ] [美]['rɪŋɪŋ]
振铃
1.
The ringing problem in digital control for this kind of process was discussed,then a concrete form of the desired closed-loop transfer function was proposed,based on which the structure of the digital controller was obtained.
该方法分析了反向响应系统控制器输出的振铃问题,给出期望闭环传递函数,并由此推出数字控制器的结构;通过分析设计参数,给出控制器单一调节参数的整定规则和获得更好控制器输出的参数选取方法。
2.
Signal integrity in the circuits design is discussed in this paper,and the major influencing factors are analyzed such as ringing,border distortion,reflection,bounce,crosstalk and jitter.
文章介绍了数字电路设计中的信号完整性问题,探讨了振铃、边沿畸变、反射、地弹、串扰和抖动等各种信号完整性问题的成因和抑制措施。
3.
At the same time it can also eliminate the ringing phenomena of the controllers.
它即可用于参数和时滞未知的或慢时变的受控对象，又可用于逆不稳定过程，并能消除控制器的振铃现象，应用范围大为拓广。
补充资料：振铃
【振铃】
（仪式）密教之修法，或为唤召诸尊，或为表欢喜而振铃也。又印度之旃陀罗振铃以别于常人云。(参见：旃陀罗)
（仪式）密教之修法，或为唤召诸尊，或为表欢喜而振铃也。又印度之旃陀罗振铃以别于常人云。(参见：旃陀罗)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条