1) bi-point(BP) design
双设计点设计
2) Design essentials
设计要点
1.
Taking a 600 MW set as an example,the design essentials of large and high temperature Selective Catalytic Reduction(SCR) reactors are being explained and epitomized.
介绍了600 MW机组使用的大型高温选择性还原反应器的结构设计要点,根据流体力学分析,确定了反应器进出口、导流器、喷氨装置的结构与布置,从而在整个空间范围内有效地控制烟气速度偏差和NH3/NOx摩尔比偏差,以满足脱硝反应的要求。
2.
The design essentials of the main electrical connection,protection configuration,and general layout of the bridge conne.
对110 kV变电所两线三变桥接线模式中的电气主接线、保护配置、总平面布置等方面的设计要点进行了探讨。
3.
The paper analyses the design essentials for automatic CIP system, mainly about flow and pressure of centrifugal pump, pipe diameter, effective volume of tank, control components, etc.
本文主要针对全自动CIP系统设计过程中清洗泵流量和扬程的确定、清洗管径及罐体有效容积的确定、控制元件设置等设计要点进行了较为全面的阐述,为CIP系统的规范化设计提供了参考依据。
3) design merit
设计优点
1.
The drawing technology characteristics of the diffuser shell was analyzed, the paper determined the drawing die structure, and simply stated the design merit of diffuser shell drawing die.
分析了扩散器壳拉伸成形工艺特点,确定了拉伸成形模结构,并简述了该扩散器壳成形模结构设计优点。
4) design feature
设计特点
1.
Analysis of design feature and operation performance of circulating fluidized bed boiler burning Fujian anthracite;
燃烧福建无烟煤的循环流化床锅炉的设计特点及运行性能分析
2.
The technical data, structural and design features about Φ140 mm entry table of piercing mill in Tianchang were introduced emphatically.
着重介绍了天长Φ140mm穿孔机进口台的技术性能、结构及设计特点。
3.
The design features of a large sulfur recovery unit in a overseas petrochemical complex processing sulfur crude are analyzed.
对国外一个大型加工含硫原油的石油化工厂的硫回收装置进行了剖析,该装置有如下设计特点:①工厂总流程和总平面布置合理,将各装置气体脱硫的溶剂集中再生,各装置的酸性水集中汽提,并将溶剂集中再生和酸性水集中汽提装置布置在硫回收装置附近;②利用尾气热焚烧炉同时处理其他装置非正常操作时排出的酸性气, 工厂无酸性气火炬;③装置规模大,操作灵活,设两套克劳斯硫回收,一套斯科特尾气处理,一套尾气热焚烧和一套尾气催化焚烧装置。
5) design characteristic
设计特点
1.
The paper summarized the main equipment collocation and design characteristic of the line.
文章总结了该线的主机配置和设计特点,生产实践表明,该生产线的设计技术指标先进,生产运行成熟可靠。
2.
Introduces the design characteristics of the PCI system and the circumstance of attaining the designed capacity and expected effects rapidly after starting-up all right of Laigang's two1000m3 blast furnaces.
介绍了莱钢两座1000m 3高炉喷煤系统的设计特点和顺利投产后迅速达产达效的情况。
3.
The design characteristics of 600k t/a grate kiln oxidized pellet project of LAIGANG Mining Co was presented in this paper As this pelletizing plant commissioned, all of pellet quality indexes were met the design requiremen
介绍了莱钢矿建公司 60万t链篦机 -回转窑氧化球团工程的设计特点。
6) design points
设计要点
1.
On the design points of the intelligent museum
智能化博物馆的设计要点
2.
The structure and design points of hard alloy drawing combination concave die were introduced in detail and provided the reference to the similar die design.
对硬质合金拉伸凹模结构及设计要点作了详细介绍,对同类型模具设计提供了参考。
3.
Using ratch cam intermittence shut-off mechanism,keeped parts on a carrier,and shut off after punching a certain length,through the concrete example,the structure principle,working process and design points of the ratch cam intermittence shut-off mechanism were introduced.
应用棘轮凸轮间歇切断机构,将制件留在一条载体上,构成一定长度后再切断成条状,通过具体实例,从棘轮凸轮间歇切断机构结构原理、动作过程、设计要点等方面作了介绍。
补充资料：1350mm双流板坯连铸机(重庆钢铁设计研究院设计)
1350mm双流板坯连铸机(重庆钢铁设计研究院设计)
叠 135Omm双流板坯连铸机(重庆钢铁设计研究院设计)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条