1) arc melt spinning
电弧快淬
2) arc-melt spinning furnace
电弧式快淬炉
3) melt-spinning
快淬
1.
Effect of quenching rate on phase transformation of Ni-Mn-Ga melt-spinning alloys;
淬速对Ni-Mn-Ga快淬合金相变的影响
2.
4)nanocomposite ribbons prepared by melt-spinning at rolling speed V=22m/s were investigated by methods of VSM.
用振动样品磁强计(VSM)研究了PrxFe94 3-xB5 7Zr1 (x=9 4 ,9 8,10 2 ,10 6 ,11,11 4 )系列快淬带在淬速V =2 2m s的淬态和真空退火态(6 70℃)样品的磁性能和磁滞回线的变化情况,发现该系列合金在淬速V =2 0m s下样品S2 (Pr1 1 Fe83 3B5 7Zr1 )取得了最好的磁性能为:Jr =0 76T ,Hc =977 3kA m ,(BH) max=98 8kJ m3;最佳快淬和晶化热处理都可以使软磁相与硬磁相耦合。
3.
The non-stoichiometric Ni50Mn27Ga23 polycrystalline ribbons were prepared by melt-spinning technique.
采用快淬技术制备了非化学计量成分的Ni50Mn27Ga23多晶薄带,对快淬薄带的马氏体相变和磁感生应变进行了研究。
4) rapid quenching
快淬
1.
The microstructures and electrochemical capacities of La_2Mg(Ni_(0.85)Co_(0.15))_9B_x(x=0 ~0.2) hydrogen storage alloys prepared by casting and rapid quenching;
铸态及快淬态La_2Mg(Ni_(0.85)Co_(0.15))_9B_x(x=0~0.2)贮氢合金的微观结构与电化学容量(英文)
2.
Effects of boron additive and rapid quenching technique on the microstructrue and electrochemical capacity of La-Mg-Ni system hydrogen storage alloy;
硼及快淬工艺对La-Mg-Ni系贮氢合金的微观结构及电化学容量的影响
3.
The effects of rapid quenching on the electrochemical characteristics of Mm(NiCoMnAl)_5B_xhydrogen storage alloys;
熔体快淬对Mm(NiCoMnAl)_5B_x贮氢合金电化学性能的影响
5) melt spinning
快淬
1.
Effects of melt spinning speed on the microstructure of Nd_(4.5)Fe_(77)B_(18.5) alloy;
快淬速度对Nd_(4.5)Fe_(77)B_(18.5)合金显微组织的影响
2.
The melt spinning microstructures of Nd8Fe86B6 are Nd2Fe14B and α-Fe phase both in the nanometer scale at the quenching rate of 12m/s;a small quantity of phase dispersed in the matrix of amorphous phase at the quenching rate of 15m/s;entirely amorphous phase at the quenching rate of 18m/s.
研究了Nd8Fe86B6合金在不同快淬速度下显微组织的变化。
3.
NdxFe84-xB16(x=4,6,8,10) alloys were prepared by melt spinning method.
采用单辊快淬法制备NdxFe84-xB16(x=4,6,8,10)合金,选取磁性能最好的Nd10Fe74B16合金为研究对象,采用特殊的退火工艺对其进行热处理。
6) melt-spun
快淬
1.
By sub-overquenching to get an amorphous mixed with fine crystallites and annealing under the optimal conditions, the melt-spun (Nd_(1-x)Pr_x)_(10.
采用部分过快淬加后续晶化退火工艺,制备出了最佳磁性能的(Nd1-xPrx)10。
2.
SmCo 5 ribbons were prepared by melt-spunning method at various wheel speeds.
采用熔体快淬法 ,在不同辊速条件下制得 Sm Co5合金条带。
3.
6 was prepared by melt-spun method.
6的Nd2Fe14B/α-Fe双相快淬粉,对快淬粉进行差热分析,并将快淬磁粉在不同的温度下进行真空热处理,之后进行X射线分析和磁性能的测量。
补充资料：快淬磁体
分子式：
CAS号：
性质：经真空熔炼成的Nd-Fe-B永磁合金，以熔融状态处在惰性气氛保护的石英坩埚中，当在压力作用下经过容器底部细孔喷射到高速旋转的水冷铜辊的外缘上，以105～106℃/S速度冷却，形成非晶态或微晶的窄薄带，再制成粉，由此制成的磁体称为快淬磁体。有利于生产过程自动化、连续化；产品内禀矫顽力及磁化强度都很高，缺点磁能积较低，一般60～80kJ/m3(8～10MGOe)。
CAS号：
性质：经真空熔炼成的Nd-Fe-B永磁合金，以熔融状态处在惰性气氛保护的石英坩埚中，当在压力作用下经过容器底部细孔喷射到高速旋转的水冷铜辊的外缘上，以105～106℃/S速度冷却，形成非晶态或微晶的窄薄带，再制成粉，由此制成的磁体称为快淬磁体。有利于生产过程自动化、连续化；产品内禀矫顽力及磁化强度都很高，缺点磁能积较低，一般60～80kJ/m3(8～10MGOe)。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条