说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 扇形孔爆破
1)  fan shaped round blasting
扇形孔爆破
1.
Application of fan shaped round blasting technque in excavation of high side slope;
扇形孔爆破技术在高边坡开挖施工中的应用
2)  deep-hole sector blasting
扇形深孔爆破
1.
The industrial test results of stope leaching at a vein-group type uranium deposit of Ganzhou Uranium Mine are introduced, with focus on upward deep-hole sector blasting, leaching technique of ore heap, as well as the critical techniques and direction of the further research.
介绍了赣州铀矿某群脉状铀矿床原地爆破浸出采铀工业性试验成果,着重叙述了上向扇形深孔爆破、采场矿堆浸出技术及进一步深入研究的关键性技术和方向。
3)  fan pattern the bottom of blasthde
孔底起爆扇形中深孔
4)  Flabellate fragment
扇形破片
5)  deep-hole blasting
深孔爆破
1.
The calculation of surface deep-hole blasting parameters of Paishanlou gold mine in Liaoning;
辽宁省排山楼金矿露天深孔爆破参数的计算
2.
Discussion on the rock fragmentation of deep-hole blasting for Guishan quarry;
龟山料场深孔爆破的岩石破碎块度问题的探讨
3.
To lower blasted boulder yield is one of the most important technical considerations in deep-hole blasting operations of mine.
降低深孔爆破落矿大块率是矿山凿岩中的一个重要课题。
6)  hole after hole explosion
逐孔爆破
1.
According to the geologic structure of the main stope,comprehensively using the advantages of hole after hole explosion and extrusion one,the demolition made breakthrough progress in the field that was difficult to be exploded.
文章分析了主采场大块率高的原因,根据主采场地质构造特点,综合应用逐孔爆破和挤压爆破的技术优点进行爆破攻关,在难爆区域取得了突破性进展,并取得了较好的经济效益和社会效益。
补充资料:深孔爆破
      孔深在5m以上的钻孔爆破技术。深孔爆破具有单位钻孔量小和炸药单位耗量低、生产效率高和便于采用综合机械化施工进行爆破、 挖装、 运输作业等优点,广泛应用于露天和地下开挖工程。深孔爆破可与预裂爆破、光面爆破和毫秒爆破等技术相结合,以获得开挖面平整、围岩稳定、提高工程施工质量的效果。
  
  
  进行深孔爆破,通常把开挖区按深度分成若干高为8~15m的梯段,逐梯段进行爆破,称深孔梯段爆破。在每一梯段,用潜孔钻或多臂钻车等沿开挖自由面布钻一排或数排垂直、倾斜或水平的深孔,前后排孔位可对应布置或相错成梅花形,用毫秒雷管控制进行爆破。梯段要素为:梯段高度H,前排孔底部抵抗线w1,排距即后排孔抵抗线w2,孔距α,钻孔直径d,钻孔深度L,超钻深度h,装药长度L1,孔口堵塞长度L2,梯段上缘至前排孔口距离 b,台阶坡面角度α1和钻孔角度α2等(见图)。前排钻孔超深是为了克服梯段底盘岩石的夹制作用,使爆后不残留根底。超深量可按h=(0.12~0.30)w1确定,松软岩石取小值,坚硬岩石取大值。深孔梯段爆破的每孔装药量可按下列公式计算:
  
  前排孔
  
  
  Q=qαw1H
  
  后排孔
  
  
  Q=KqαbH
  式中Q为每孔装药量(kg);q为单位耗药量(kg/m3);K为受前排石渣阻力影响系数,取1.1~1.2;其余符号的单位均以m计。
  
  为了克服炮孔底部所受夹制作用,大部分炸药应集中装在底部,孔口的堵塞长度一般不小于最小抵抗线,所以在确定梯段高度和抵抗线大小时,要与炮孔直径的选择相适应。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条