1) injection probe
电流注入探头
1.
The simulated models are compared with the experimental characterization of the injection probe, and the result shows the transmission line model is more identical with actual conditions than the lumped-parameter circuit model.
电流注入探头作为一种高效的大电流注入技术广泛运用于电磁兼容性试验。
3) injection current
注入电流
1.
Theoretical analysis and characterization of injection current distribution and influences on optical near-field modes in gain-guided vertical-cavity surface-emitting lasers;
增益导波垂直腔激光器注入电流空间分布及其对激光近场模式影响的理论分析和表征
2.
After the node sequence injection current is got,considering the influence from other sequence components,the following solution is applied:for positive and negative sequence problems ,node voltage is solved by for/backward sweep method;for zero sequence problem,node voltage is.
在求得各序间相互影响各序节点注入电流之后,采取以下求解方法:对正序、负序网络沿辐射支路用前推回代的方法求解,对零序网用常规高斯塞德尔(Gauss-Seidel)迭代法求解,这样可加快求解的速度。
3.
This paper proposes an injection current based three phase power flow method.
提出了节点注入电流的三相潮流分析方法。
4) current injection
电流注入
1.
This paper introduces the method to achieve time association in current injection experimentation.
本文介绍了在电流注入试验中实现时间关联的方法,并采用该方法得到了典型电路失效概率分布。
2.
In this paper,the EMP failure modes of solid state relays were obtained by current injection method.
本文通过电流注入法对某型直流固态继电器输入端与输出端的电磁脉冲损伤机制进行了实验研究,确定了两种失效模式。
3.
The electromagnetic pulse(EMP) damage mechanism and failure modes are obtained for the input port and output port of solid state relays by current injection method.
采用电流注入法对某型直流固态继电器输入端与输出端的电磁脉冲损伤机制及失效模式进行了实验研究,结果表明:输入端注入电磁脉冲信号时,输出端会产生误动作,并可造成输入电路中三极管BE节产生短路损伤,导致输入端施加控制信号时输出端无法导通;输出端注入电磁脉冲信号时,可造成输出电路中MOSFET管的栅极和漏极产生短路损伤,导致输出端短路。
5) Current bleeding
电流注入
1.
A current bleeding CMOS mixer with complementary transconductance stage is designed.
设计了一种基于跨导互补结构的电流注入混频器,通过在吉尔伯特混频器电路的本振开关管源极增加PMOS管形成电流注入电路减小本振端的偏置电流,改善电路的闪烁噪声和增大电路的增益。
6) current probe
电流探头
1.
The results of low frequency interference current probe made from ferrite and from Fe based and Co based amorphous alloy, were compared and analyzed.
通过对铁基、钴基非晶合金与铁氧体软磁材料的性能和实际实验结果的分析、比较 ,由于非晶合金自身良好的磁性能 ,将其用于电磁兼容性试验设备中作为低频干扰电流探头的磁芯材料 ,实验证明选用铁基、钴基非晶合金 ,可使电流探头的检测灵敏度、精确度大大提高 ,从而为扩大非晶合金这一功能性材料的应用范围提供了实验依
2.
The principle for calibrating the current probe is introduced in this paper.
介绍了电流探头传输阻抗的校准原理,并对测量不确定度进行了详细的分析评定。
3.
A new approach using two current probes to measure SMPS conducted noise is introduced.
对传统测量开关电源传导干扰方法的优缺点进行了比较,并在此基础上提出了一种基于双电流探头的新测量方法,它可在不中断开关电源正常工作的情况下测量共模和差模干扰,并能在开关电源电磁干扰频率范围内获得较精确的干扰模型。
补充资料：标准冲击电流波形(见冲击电流发生器)
标准冲击电流波形(见冲击电流发生器)
standard impulse current wave form
blaozhun ehonglld}0n4一u box]ng标准冲击电流波形(standard impulse currentwave form)见冲击电流发生器。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条