1) Overlay strata thickness
上覆岩层厚度
2) overlying rock minimum thickness
上覆岩层最小厚度
3) rock covering thickness
岩石覆盖层厚度
1.
Combined with subsea tunnel engineering at eastern route way in Xiamen,the minimum rock covering thickness of subsea tunnel,water pressure design values,section optimization of lining structure and waterproof and drainage project,construction measures throughout bad subsea geology section,such as fault,solution groove,necessity of service tunnel setting were analyzed.
结合厦门东通道海底隧道工程,对海底隧道最小岩石覆盖层厚度、水压力设计值的确定,衬砌结构断面优化与防排水方案,穿越海底不良地质段(断层、溶槽)的施工措施及服务隧道设置的必要性问题进行了分析。
4) rock cover thickness
覆岩厚度
1.
Based on the results of a practical example, the effects of sea depth and rock cover thickness on the stress fields are analyzed with the consideration of seepage fields.
通过实例计算,分析了渗流场作用下,海水深度和覆岩厚度对隧道应力场的影响规律。
5) overburden density
上覆岩层密度
6) overlying strata
上覆岩层
1.
Analysis on the mechanism of the face-contacted blocks structure in overlying strata above the longwall face;
采场上覆岩层面接触块体结构的力学机理分析
2.
Analysis on the damage zone of overlying strata and safety layer distance on the upward mining above the longwall goaf
长壁开采上覆岩层损伤范围及上行开采的层间距分析
3.
Based on the experiment with similar material,the laws of the extra subsidence on the surface and the stress vary inside overlying strata by newly increased load on the surface above worked-out area formed by fully mined and partial mined were researched.
通过相似材料模拟实验,研究了全部开采和部分开采条件下的采空区在地表新增荷载后,地表附加沉降和采空区上覆岩层内应力的变化规律。
补充资料：有机覆层:有机覆层
在基体材料表面覆以有机材料的材料保护层。在机械製造中﹐有机覆层的绝大部分是涂装层﹐或称油漆层。此外﹐也有用橡胶或塑料作为覆层的。需要抗酸﹑硷和抗腐蚀性气体和液体的钢铁件﹐常用厚约 3毫米的橡胶(如氯丁橡胶)或塑料(如氯化亚乙烯共聚物)黏在表面﹐可长期保护基体不受腐蚀。这种覆层主要用在大型抗蚀容器或排气系统中。埋在土壤中的金属构件﹐常以聚乙烯带包裹保护。在喷鉬或喷不锈钢的表面上涂覆聚四氟乙烯﹐在150℃温度下摩擦係数很低﹐磨损轻微﹐适於製造低载荷和要求高度清洁的滑动轴承﹐或用在食品﹑精细包装和纺织机械上。各国的Du﹑Dx轴承都是以塑料与金属复合製成的。通过静电喷涂将环氧树脂﹑氯化聚醚﹑聚四氟乙烯以及聚氯乙烯等塑料粉末涂覆在金属表面﹐可获多种抗化学腐蚀性极好的覆层﹐可用於输水﹑污水处理和海洋平台的设备上。有机覆层在辉光放电情况下﹐有机单体可以聚合成无针孔的有机膜﹐用作电容器的介质层。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条