说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 窗墙相关性控制原理
1)  interrelation principle between window and wall
窗墙相关性控制原理
2)  correlation theory
相关性原理
3)  correlation principle
相关性原理
1.
High frequency parameter measurement of the power line trap based on the correlation principle;
提出了一种利用相关性原理测量高频电力阻波器的频率阻塞特性的方法,详细阐述和分析了利用一对同频正交参考信号对待检信号进行相位检测处理的过程,并总结出了一套实用的阻波器阻抗及电阻分量的计算公式,避免了繁琐的三角函数运算。
4)  Bose-Einstein condensation and superfluid phenomena
波聚相关性原理
5)  correlation theory
相关原理
1.
On the basis of correlation theory to identify the magnitudes and phase values of unbalance.
介绍了微速差双转子系统的动平衡原理,根据相关原理准确得到内外转子不平衡量大小和相位,结合虚拟仪器技术在LabVIEW下开发的测试程序,实现微速差双转子系统的动平衡,并在卧螺离心机上进行了实验验证。
2.
A new method based on correlation theory to accurately measure phase difference between electrical signals and their frequency is proposed.
提出了一种基于相关原理的电信号相位差准确测量方法,在同步采样条件下,对电压、电流信号作归一化处理后得到的2信号的互相关函数在初始时刻的值直接反映了它们之间的相位差。
3.
On the basis of correlation theory,this paper presents a method named Single Point DFT" to identify the unbalance.
不平衡矢量的识别是小速差双转子系统现场动平衡的关键,文中根据相关原理提出了单点DFT不平衡矢量识别方法,通过理论分析确定了相关积分时间及其可能的误差。
6)  correlation principle
相关原理
1.
When measuring the electrical characteristics of periodic signals using intelligent instruments based on the correlation principle,errors caused by non-integer-period sampling cannot be eliminated completely due to hardware restrictions.
利用基于相关原理的智能仪器测量周期信号的各种电参数时,由于硬件条件的限制,非整周期采样所致误差无法被完全消除。
2.
Based on the Kirchhoff diffraction theory, the necessary condition for keeping the correlation of the complex amplitudes of the ultrasonic speckles back scattered from an interface in rigid body motion is deduced by applying the correlation principle.
在Kirchhoff衍射理论的基础上 ,应用随机信号相关原理 ,推导了作刚体运动的界面上反射超声散斑在空间运动时 ,保持其复振幅相关的必要条件 。
补充资料:模具加工时FANUC先行控制相关参数调整

一、0MC/0MD 
  
参数号码       参数含义           典型设定       备注
45#3        切削进给插补后直         1         635为时间常数
             线加减速有效
393#0      自动拐角降速功能有效      1         如果拐角要求
                                                高时设1 395#2      切削进给插补后直线加      1
           减速有效(先行控制)
395#3      依速度差控制拐角降速      1         482,483,
                                                487设定
395#6       插补前直线加减速         1
             类型B有效
399#2      前馈控制对切削进给                   通常设0
            和快移均有效
399#4      依进给类型的在位检        0

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条