1) variable tooth thickness plane worm gear transmission
变齿厚平面蜗轮传动
1.
The full name of variable tooth thickness plane worm gear transmission is Backlash adjustable plane worm gear with variable tooth thickness enveloping worm transmission,which is a new kind of accurate power transmission that is intervenient between traditional motion transmission and power transmission.
变齿厚平面蜗轮传动的全称为“侧隙可调式变齿厚平面蜗轮包络环面蜗杆传动”,它是介于传统“运动传动”和“动力传动”之间的一种新型精密动力传动。
2) planar worm gear
平面齿蜗轮
1.
To resolve the problem of low efficiency of single disc-milling-cutter for planar worm gear manufacturing, a novel approach that a Single-tooth Flying Cutter Manufacturing (SFCM) was used to cut planar tooth worm gear index-continuously was developed.
针对单角度盘铣刀加工平面蜗轮效率低等缺点,提出了一种用单齿飞刀连续分度加工平面齿蜗轮的方法。
3) gear thickness
蜗轮齿厚
1.
With common normal line measure and approximately calculate gear thickness of worn wheel;
用公法线测量并近似计算蜗轮齿厚
4) worm helical gear transmission
蜗杆斜齿轮传动
1.
Using mechanical transmission test table to carry out comparative test between the worm helical gear transmission and worm wheel transmission,this paper analyzes the feasibility of replacing worm wheel transmission with cylindrical worm helical gear transmission.
圆柱蜗杆斜齿轮传动是在传统的蜗杆蜗轮传动中用斜齿轮取代蜗轮而形成一种新的蜗杆传动形式。
5) worm-gear drive
蜗杆齿轮传动
6) side-worm gears
端面传动蜗轮副
补充资料：传动：少齿差行星齿轮传动
由一对齿数相差很少的内嚙合齿轮和输出机构组成的行星齿轮传动。通常齿数差为1～4。外齿轮通过轴承和偏心套装在减速器的输入轴上(见图 销轴式少齿差行星齿轮传动 
)。为了平衡部分惯性力和提高承载能力﹐通常採用两个外齿轮﹐偏心套上有两个偏心并互成180°。内齿轮大多固定不动。输出机构将外齿轮的转动通过销轴传到输出轴上﹐并保持它的角速度不变。常用的输出机构有销轴式和浮动盘式等。渐开线少齿差单级传动一般採取的传动比为20～100以上﹐效率为0.8～0.9。它的齿轮可用一般齿轮机床加工。如外齿轮的齿数为Z ﹐内齿轮的齿数为Z b﹐则内齿轮固定时﹐输入轴和输出轴的传动比b＝－Z /(Z b－Z )﹔输出轴(F )不动时﹐输入轴和内齿轮的传动比＝Z b/(Z b－Z )。内﹑外齿轮的齿数差越少﹐每级传动得到的传动比越大﹐但齿数差少到一定程度时﹐例如採用压力角为20°的标準渐开线齿轮﹐当内齿轮数少於180﹑齿数差少於5～7时﹐内嚙合齿轮就会產生齿形重叠干涉。解决的办法是採用短齿并进行适当的变位。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条