1) compression modulus
抗压弹性模量
1.
The uncertainty of compression modulus of elastomeric pad bearing.
本文根据JJF 1059-1999《测量不确定度评定与表示》的要求,系统地对公路桥梁板式橡胶支座的抗压弹性模量检测结果的不确定度进行了研究。
2.
The uncer tainty of compression modulus of elastomeric bearing pads is evaluated and resea rched.
本文根据JJF1059-1999《测量不确定度评定与表示》的要求,系统地对公路桥梁板式橡胶支座的抗压弹性模量检测结果的不确定度进行了研究。
2) compressive elastic modulus
抗压弹性模量
1.
Four regressive equations which will provide reference for engineering practice were approached, including growth rate of compressive/tensile elastic modulus with age, compressive elastic modulus with age, compressive elastic modulus with strength.
本文在总结国内大量碾压混凝土工程试验数据的基础上对碾压混凝土静力弹性模量进行分析,提出碾压混凝土抗压及抗拉弹性模量增长率、抗压弹性模量与龄期以及抗压强度与抗压弹性模量的关系式,从而可以为工程设计和试验提供理论参考。
2.
In construction,high fluid and large volume fly-ash concrete is successful application through availably reducing compressive elastic modulus by increasing the dosage of fly-ash,and good effect is achieved.
施工中成功地应用了高流态高掺量粉煤灰混凝土,通过加大粉煤灰的掺量来有效降低抗压弹性模量,取得了很好的效果,并为刚性混凝土防渗墙的研究发展开拓了一个良好的方向。
3) Compression modulus of resilience
抗压回弹模量
1.
A series of indoor experiments have been done to study compressive strength, compression modulus of resilience and cleavage strength.
在对冷再生混合料的配比和力学性能(抗压强度、抗压回弹模量和劈裂强度)室内试验的基础上,探讨了冷再生混合料力学性能的变化规律以及其影响因素。
4) compression rebound modulus
抗压回弹模量
1.
Through the research on unconfined compressive strength and compression rebound modulus of cement stabilized aggregate in laboratory,and after analyzing the factors which affect these two indexes separately,the relationship between unconfined compressive strength and compression rebound modulus of cement stabilized aggregate is expressed.
通过室内试验研究水泥稳定碎石基层混合料的无侧限抗压强度和回弹模量,并对其各自影响因素进行分析,对水泥稳定基层的抗压回弹模量与无侧限抗压强度之间的关系作了论述。
2.
The compression rebound modulus at different ages were tested with top surface measuring method,and the modulus development law with age was drawn.
为得到半刚性基层不同龄期的弯沉检测标准,在室内成型二灰土和二灰碎石试件,并在标准条件下养生;采用顶面法测定试件不同龄期的抗压回弹模量,得出其模量随龄期增长的规律,将其代入弹性层状体系理论简化公式中,得出不同龄期半刚性基层顶面弯沉值计算公式,并给出其实例应用的说明。
5) Resilient Modulus
抗压回弹模量
1.
Estimating Resilient Modulus of Asphalt Treated Permeable Base Materials;
沥青稳定碎石排水层材料的抗压回弹模量
6) Modulus of elasticity
抗弯弹性模量
1.
The objective of this study is to compare three nondestructive methods for evaluating the bending modulus of elasticity(MOE),modulus of rupture(MOR) and compressive strength parallel to grain(σ_c) of Eucalyptus grandia×E.
首先采用3种无损检测设备获得无疵小试样的动态弹性模量,然后进行抗弯弹性模量(MOE)、抗弯强度(MOR)和顺纹抗压强度(σc)的测定,并分析3种无损检测结果与木材强度性质的关系。
2.
The restrain conditions were the design goal of plywood modulus of elasticity parallel and perpendicular to the face grain,panel thickness and number of plies.
从单板压缩率和铺设角度入手,以每层单板厚度为设计变量,单板厚度的加权和最大值为目标函数,同时以胶合板顺纹、横纹抗弯弹性模量和总厚度满足给定设计目标为约束条件,建立了速生树种胶合板弯曲弹性性能优化设计模型。
补充资料：表观弹性模量
分子式：
CAS号：
性质： 在减震橡胶制品中，由于橡胶与金属黏着界面的形状效应，不能仅由形状尺寸和橡胶的弹性模量来决定不同方向的弹簧常数，为此将表观弹性模量Eap定义为：圆柱形：Eap=(3+4.9355S2)G正方形：Eap=(3+6.580S2)G无限长柱：Eap=(4+3.290S2)G式中G为剪切弹性模量，S为形状因子。
CAS号：
性质： 在减震橡胶制品中，由于橡胶与金属黏着界面的形状效应，不能仅由形状尺寸和橡胶的弹性模量来决定不同方向的弹簧常数，为此将表观弹性模量Eap定义为：圆柱形：Eap=(3+4.9355S2)G正方形：Eap=(3+6.580S2)G无限长柱：Eap=(4+3.290S2)G式中G为剪切弹性模量，S为形状因子。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条