1) EM shielded room
电磁屏蔽室
1.
This article profoundly analyses the reason of the debase of EM shielded room s shielding effectiveness brought by opticalfiber from the stump of Maxwell Equation,and gives the derivation of some formulas relative to the problem.
以Maxwell方程为基础,对电磁屏蔽室因截止波导管穿光纤引起的屏蔽效能降低的现象进行了深入的理论分析和相关公式推导,得出了根据实际应用进行修正的公式和方法。
2) magnetic shielding room
磁屏蔽室
1.
An approach to a compound equipment composed of a three axe Helmholtz coil system set inside a magnetic shielding room has been made.
探讨了一种在磁屏蔽室内套装三轴亥姆霍兹线圈系统的复合装置。
3) electromagnetic shielding
电磁屏蔽
1.
Design and research on non-conductive short carbon fibers in electromagnetic shielding coating;
电磁屏蔽涂料用改性短碳纤维的研究
2.
Preparation and properties of transparent metallic mesh electromagnetic shielding structure;
金属丝网透明电磁屏蔽层材料制备与性能研究
3.
Study of electroconductive adhesive for electromagnetic shielding;
电磁屏蔽与导电胶粘剂研制
4) electromagnetic shield
电磁屏蔽
1.
The electromagnetic shield for radio-frequency tumor hyperthermia system;
肿瘤射频热疗机房的电磁屏蔽系统
2.
Technical application of electromagnetic shield for military electric power plant;
军用电站的电磁屏蔽技术应用
3.
Research status of fillers in electromagnetic shielding rubber;
电磁屏蔽橡胶用填料的研究现状
5) electromagnetism shield
电磁屏蔽
1.
Polyvinyl chloride(PVC)based electromagnetism shield coating was prepared.
报道了聚氯乙烯(PVC)基材的复合型电磁屏蔽涂层的研究。
2.
So the electromagnetism shield and the digital fi.
采用电磁屏蔽和数字光纤传输技术等措施,不但较好地解决电磁干扰难题,并将等离子体负载电压和电流、身管膛内压力、炮口压力和测量炮口速度的区截装置等信号统一在一个时间轴上,为电热炮的等离子体点火、增强作用的理论研究找到可行的试验方法。
6) electromagnetic interference shielding
电磁屏蔽
1.
Composite plastic containing graphite embedded with magnetism particles for electromagnetic interference shielding;
氧化铁-石墨/ABS复合材料制备及电磁屏蔽性能
2.
The species of electromagnetic interference shielding material and the characteristic of dope and filling that were used in shielding material were reviewed.
阐述了研究电磁屏蔽材料和吸波材料的重要性,分析了在不同情况下电磁屏蔽材料和吸波材料的作用机理。
补充资料：电磁波屏蔽材料
分子式：
CAS号：
性质：能屏蔽电磁波干扰的材料。制法有：(1)在电器外壳上涂镀低熔点金属的金属层，或是在表面涂敷混有金属粉的导电性涂料；(2)用含金属的纤维或含导电成分的树脂配合料制成金属屏蔽壳。所制成的膜或壳的导电率至少应在10S/cm以上。
CAS号：
性质：能屏蔽电磁波干扰的材料。制法有：(1)在电器外壳上涂镀低熔点金属的金属层，或是在表面涂敷混有金属粉的导电性涂料；(2)用含金属的纤维或含导电成分的树脂配合料制成金属屏蔽壳。所制成的膜或壳的导电率至少应在10S/cm以上。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条