说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 多斜孔板
1)  inclined multi-hole plate
多斜孔板
1.
Experiments were conducted to investigate the flow coefficients and cooling effects of 8 different inclined multi-hole plates by using the similitude method of mass/heat transfer.
针对8种不同孔板结构的多斜孔板,应用传质/传热相似方法,进行了流量系数和冷却效果的试验研究。
2)  combined column plates with slopping holes
多溢流复合斜孔塔板
3)  oblique hole tray
斜孔塔板
1.
Application of oblique hole tray in the treatment of sewage containing methanol in YULIN gas field;
斜孔塔板在榆林气田含醇污水处理中的应用
2.
On the base of traditional ammonia still process, the course of ammonia distillation is simulated and optimized by PRO/II software, and the new multiple overflow and composite oblique hole tray is applied to correct the old process, then the new distillation unit is established.
在传统蒸氨工艺基础上,将氨蒸馏分离采用PRO/II软件化工过程模拟优化,并采用新型多溢流复合斜孔塔板,修正原工艺中的不足,建了新的化工蒸馏单元。
3.
The text introduced our company present situation and reforming program of the oblique hole tray.
介绍了公司粗苯系统脱苯塔的现状及脱苯塔的改造方案,通过采用斜孔塔板后,脱苯效率明显提高,生产运行顺利,投资少见效快。
4)  slant hole tray
斜孔塔板
1.
The trays in the distillation column were designed with new multi overflow compound slant hole trays commonly used in the recent years.
在此基础上对原有工艺和新工艺精馏塔板进行设计 ,塔板选用近年来广泛应用的新型多溢流复合斜孔塔板。
2.
The results are satisfied to use the slant hole trays which have good anti - blockin.
本文介绍在燕山石化公司化工一厂制苯车间裂解汽油加氢工段和茂名乙烯装置裂解汽油加氢工段应用斜孔塔板的情况,生产情况表明斜孔塔板具有较强的抗堵塞性能,在维持该装置长周期稳定生产中有良好作用。
5)  multi-hole orifice
多孔孔板
1.
Experimental study on main factor affecting throttling characteristic for multi-hole orifice;
多孔孔板节流特性主效应因素试验
2.
Experimental study on water throttling model of multi-hole orifice;
多孔孔板水节流特性试验及数学模型
6)  effusion wall
多斜孔
1.
Influence of aerodynamic parameter on the temperature gradient and cooling efficiency for effusion wall cooling method;
多斜孔冷却方式气动参数对壁温梯度和冷却效率的影响
2.
Experimental investigation of the temperature gradient and cooling efficiency for effusion wall cooling methods on combustion liner;
火焰筒多斜孔冷却方式壁温梯度和冷却效率试验
补充资料:斜楔式侧孔冲模

工件套在件6上用件9上的台阶定位,而件9用件18防转并且起到圆周方向定位的作用,当上模下行时,件5先将工件压牢,上模继续下行时,由斜楔4推动件11和装在件11上的件8完成冲孔工作。当上模上升时件11在件4的作用下退回,按下件16,工件由与件16相连的件9顶出.




 



工件图


 



 



 



 


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条