说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 轴向跑偏
1)  axial-misalignment
轴向跑偏
1.
Based on the analysis of the belt misalignment of the metal V-belt type CVT,the mechanism of the belt axial-misalignment was discussed and several methods which can eliminate the axial-misalignment was introduced.
通过对金属带式无级变速器传动钢带的轴向跑偏的分析,阐述了产生钢带中心线轴向跑偏的机理,介绍了消除传动钢带轴向跑偏的几种方法,并指出了采用曲母线带轮或改变无跑偏时的速比等控制方法的不足,为此,提出了一种电液控制方法,为消除传动钢带的轴向跑偏,取得了良好的效果。
2)  axial alignment tolerance
轴向偏差
1.
Research results indicate that when the single ball lens is used in the LD-ball lens-SMF system,the axial alignment tolerance is ±30 μm,the lateral alignment tolerance is ±1.
结果表明:当采用单球透镜时,所带来的轴向偏差为±30μm,横向偏差为±1。
3)  axial offset
轴向偏移
1.
The paper introduces excess loss based on lateral offset,axial offset, longitudinal offset, and different parameter value within a fiber splice, then, discusses the measurement method of excess loss.
介绍了光纤接续中由横向偏移带来的、轴向偏移造成的、纵向偏移产生的以及被接光纤具有不同的参数时所造成的附加衰减产生的机理及其测试方法。
4)  Axial offset-focus
轴向偏焦
5)  axial deflection
轴向偏斜
1.
To reduce the metal belt\'s axial deflection of the metal belt continuously variable transmission(CVT) during the working process,the value of the axial deflection has been calculated by using numerical methods.
为了减少金属带式无级变速器中金属带在工作过程中的轴向偏斜,采用数值求解的方法计算轴向偏斜的大小,比较了两种计算轴向偏斜方法的精度,得出了和实际工况更接近的算法;根据共轭曲线原理,以金属带渐开线母线为例,求解出了与之共轭的带轮母线,得出了带轮母线曲率和带轮接触强度的关系,通过改变金属带的设计参数,可以改善带轮和金属带受力状态,保证了变速过程中金属带轴向作整体平移,在理论上消除了金属带的轴向偏斜,提高了金属带的寿命和传动的可靠性以及无级变速器的性能,为金属带式无级变速器的设计提供参考。
6)  running deviation
跑偏
1.
This paper analyzes the running deviation of conveyor belt,puts forward precautionary measures of running deviation under different situation,studies on corrective measures,self-corrective measures and its principle in de.
输送带跑偏是带式输送机运行中最常见的故障,严重影响设备的寿命及生产。
2.
In aluminium strip hot rolling process,because the landscape orientation parameters of the workpiece and the rolling mill are not even,there is always departure between the center line of the workpiece and the assumed center line,which is called running deviation.
铝带热连轧过程中,铝带和轧机横向特性参数不均易引起铝带中心线偏离轧制系统设定中心线,产生跑偏现象。
3.
This paper introduces the reasons of belt coveryor's belt running deviation,and some methods to adjust deviation.
介绍带式输送机输送带跑偏的原因 ,以及调偏的一些方法。
补充资料:跑了和尚跑不了寺
1.见"跑了和尚跑不了庙"。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条