说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 点对应
1)  point correspondence
点对应
1.
To meet the requirements of the point correspondence of two images, a Template Based Area Weight Signing Edge Detection Method(TBAWSED) using the region density feature is put forward, and a fast point correspondence strategy based on ABM(Area Based Method) and FBM(Feature Based Method) is presented.
根据两幅图像间点对应的要求,利用像素所在区域强度的变化,提出了一种基于模板的区域权值标记边缘检测方法(TBAWSED)。
2)  P2P
点对点应用
3)  corresponding point
对应点
1.
In order to obtain the ideal processing result ,when the NC processing program is compiled ,should act according to special details of the part,correctly determine corresponding points position and quantity of up and down surface,correctly input H1 H2 and HCD these three parameters,correctly assigns XY surface and UV surface.
通过在编制加工程序时从上下异形零件的加工原理出发,依据零件的具体情况,正确确定上下面上的对应点的位置和数量,正确输入H1(下导轮中心到工作台面的距离)、H2(被加工工件的厚度)、HGD(上、下导轮中心之间的距离)这三个参数,正确指定XY面(编程面)及UV面(参考面)是加工成功的关键。
2.
This paper propose a novel method of Reconstruction of Vessel Axis on matching of multi-resolution projections and analyzing of corresponding points.
提出了一种多分辨投影匹配与对应点分析相结合的血管轴重建方法。
4)  Corresponding points
对应点
1.
This paper analyzes the characterestics of laid abnormity faces, points out that getting the corresponding points is the key for programming the laid abnormity faces.
分析了直纹异形面的特点,指出正确确定上下编程轨迹的对应点是异形面编程的关键。
2.
The key of the ASMs is how to search the corresponding points of the landmarks in the ASMs.
主动形状模型是一种以迭代的方式形变以匹配新图像中的目标实例的统计形状模型,它的关键是如何搜索形状模型标记点的对应点。
5)  vertex correspondence
顶点对应
6)  Corresponding vertex
对应顶点
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条