说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 相对抗扭刚度
1)  relative anti-twisting rigidness
相对抗扭刚度
2)  torsional rigidity
抗扭刚度
1.
The studes on adjustment torsional rigidity of torsion bar;
调整弹性零件抗扭刚度的研究
2.
This article simplely introduced torsion pendulum's parameters, and practial tested torsional rigidity of slivers.
本文简单介绍了测量条子抗扭刚度的扭摆仪及其特点,并实际测量了几种常见条子的抗扭刚度。
3.
The lateral rigidity and torsional rigidity of the wall is enhanced and the pertinence contexture is strengthened by configuring of vertical structure rationally and after the actual analysis and calculation for the specific project.
小高层住宅采用短肢剪力墙结构,可以不露墙柱,减轻重量,减小地震效应等优点;通过具体工程实际分析计算,合理的布置竖向结构,提高其侧向刚度和抗扭刚度,并针对性的构造加强,在7度地震区,小高层住宅采用短肢剪力墙结构,其抗震性能尚可。
3)  torsion stiffness
抗扭刚度
4)  torsion rigidity
抗扭刚度
1.
For a multi-cracked prismatic shaft torsion problem example,an optimized project of Back-propagation training is introduced by using Neural Network toolbox in MATLAB software,and the project is explained in detail and the good learning scheme is given by simulating the experimental results of the torsion rigidity.
最后对柱体的抗扭刚度实验值进行快速拟合,得到了裂纹尖端的应力强度因子K3。
5)  torsional stiffness
抗扭刚度
1.
Torsional stiffness of tower crane mast is closely related with the arrangement of Web members of the mast.
塔式起重机塔身的抗扭刚度与塔身腹杆布置密切相关。
2.
In this paper,the prestressing scheme of back diagonals of large miter gates and its analysis technique are discussed,and in connection with some conventional types of miter gates,the torsional stiffness,steel consumption and usage factors are investigated and compared.
本文讨论了大型人字门背拉杆的预应力方案及其分析方法,并针对几种不同门型,详细研究比较了它们的抗扭刚度、用钢量和用钢效率。
3.
Based on the analysis of the experiment,it studied the deformation capacity of the SRC in a state of pure torsion,and further discussed the impact of component factors of torsional stiffness.
在试验的基础上分析了SRC构件在纯扭状态下的变形能力,并进而讨论了构件抗扭刚度的影响因素,从而为SRC构件抗扭刚度的理论研究做了必要的准备。
6)  twisting stiffness
抗扭刚度
1.
Then relative twisting angle and twisting stiffness of soft wire shaft are obtained.
根据钢丝软轴基本参数的变化,确定其受载后其它几何尺寸的变化量,由此导出软轴两端相对扭转角进而得到钢丝软轴抗扭刚度的计算公式。
补充资料:对抗性矛盾与非对抗性矛盾
      反映两类不同性质的矛盾的哲学范畴。社会生活中复杂多样的矛盾,按其性质不同,可分为对抗性的和非对抗性的两种类型。对抗性矛盾是指矛盾双方在根本性质和根本利益上互相敌对、不可调和的矛盾,其斗争形式一般表现为剧烈的外部冲突。在阶级社会中,剥削阶级和被剥削阶级的根本利益对立,其矛盾的性质是对抗的。一般要通过双方的激烈斗争和剧烈的外部冲突的形式加以解决。非对抗性矛盾是矛盾双方在根本利益一致基础上的矛盾,一般不表现为剧烈的外部冲突,即不表现为对抗的形式。对抗性矛盾和非对抗性矛盾,主要用来说明社会生活中的矛盾,但有时也指自然界中的某些矛盾。
  
  正确区分对抗性与非对抗性矛盾,采取与矛盾性质相适应的斗争形式,是无产阶级政党正确区分和处理敌我矛盾和人民内部矛盾的理论基础。敌我矛盾是对抗性的矛盾,人民内部矛盾是非对抗性的矛盾;对敌我矛盾一般要采取革命的方法解决,在社会主义制度下,则要按照法律程序采取专政的方法解决;对人民内部矛盾,则必须采取民主的方法解决。不能混淆两类不同性质的矛盾,采用不适当的斗争形式。
  
  研究对抗性矛盾与非对抗性矛盾,既要注意它们的根本区别,又要注意它们的联系和在一定条件下的互相转化,从而相应地改变斗争形式。对抗性的矛盾,一般要采取对抗的斗争形式,但在一定条件下也可以采取非对抗的斗争形式加以解决。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条