1) energy loss
能损
1.
With the difference between the actual flue gas temperature and rated one in the various heating surfaces of a utility boiler serving as characteristic data a fuzzy pattern identification based model has been set up for energy loss identification.
以电站锅炉各部分受热面烟温与额定烟温的差值为特征参数 ,建立了基于模糊模型识别的三种能损类型漏风 ,污染和煤质变劣的模糊模式识别模型。
2.
The energy losses of cluster ions H + 2, H + 3, H + 4, H + 5 and H + 7 with energy of 260-450 keV/p in solid films have been measured.
研究了每核子能量为 2 6 0— 4 5 0keV的H+ 2 ,H+ 3 ,H+ 4 H+ 5和H+ 7团簇离子在金膜中的能损 。
2) energy dissipation,energy loss
能量损耗<能>
3) wear behavior
磨损性能
1.
Effect of laser treatment on wear behavior of 4Cr3Mo2NiVNb steel;
激光处理对4Cr3Mo2NiVNb钢磨损性能的影响
2.
Study on microstructure and wear behaviors of MoS_2/TiC/Ni composite wear-resistant coating by laser cladding;
激光熔覆MOS_2/TiC/Ni减摩耐磨复合涂层组织及磨损性能的研究
3.
Sliding friction and wear behavior of the plasma sprayed Cr_2O_3 coating by ion implantation were studied at ambient condition on a pin-on-disc tester.
采用离子注入技术对Cr2O3涂层表面进行氮离子注入处理,用俄歇电子能谱仪、微区X射线衍射仪及X射线光电子能谱仪分析氮离子注入改性层的相组成及其氮元素沿层深的浓度分布,用销-盘式摩擦磨损试验机考察了注入前后Cr2O3涂层的磨损性能,用扫描电子显微镜观察其磨痕表面形貌及摩擦界面间的物质转移。
4) wear properties
磨损性能
1.
The mechanical and wear properties of (Al3Zr+Al2O3)p/Al composites are studied.
运用Al-Zr(CO3)2体系熔体反应法制备了(Al3Zr+Al2O3)p/Al复合材料,研究了(Al3Zr+Al2O3)p/Al复合材料的力学和磨损性能。
2.
The friction and wear properties of the composites in sliding against GCr15 bearing steal were investigated on MM200 wear tester in dry friction condition.
用MM 2 0 0型磨损试验机评价了不同样品在干摩擦定载荷条件下的磨损性能 ;用扫描电子显微镜 (SEM)对试样的磨损表面进行了观察分析。
5) wear resistance
磨损性能
1.
Microstructure and wear resistance of laser cladding Co+Ni/WC alloy composite coating;
激光熔覆Co+Ni/WC复合涂层的组织和磨损性能
2.
The microhardness and wear resistance of the laser clad layer were examined.
利用XRD,SEM和TEM等分析了激光熔覆层的相组成及微观组织,并测试了激光熔覆层的显微硬度和磨损性能。
3.
Microstructures and wear resistance of the coating were investigated by SEM,XRD and MM200 wear tester.
为了解决含沙油润滑条件下材料的磨损问题,采用高速电弧喷涂技术制备了3Cr13钢涂层,使用SEM、XRD及MM200摩擦磨损试验机测试了涂层的组织结构及在含细沙油润滑条件下的磨损性能。
6) Wear Property
磨损性能
1.
Study on wear property of PTFE/metal selflubricating composites;
PTFE/金属自润滑复合材料的磨损性能研究
2.
At the same time,residual stresses of Ni-P alloy film coated on silicon substrate by laser heat treatment were measured,and effects of residual stress of the film on wear property and interfacial bonding strength were analyzed.
用扫描电镜(SEM)观察了化学沉积Ni-P合金薄膜/单晶硅基体的结构与颗粒度,利用X射线衍射(XRD)技术测试了其化学沉积后的残余应力,测量了激光热处理后残余应力的变化规律,分析了残余应力对磨损性能及界面结合强度的影响。
3.
The results show that the order of parameters affecting the wear property from major to minor is spray distance L,hydrogen flow GH2,plasma current I1 and argon gas flow GAr.
通过正交试验分析了大气等离子喷涂中经常需要调整的工艺参数,即电弧电流、氩气流量、氢气流量和喷涂距离对Cr2O3涂层磨损性能的影响,并进行了磨痕的显微形貌观察和能谱分析。
补充资料：δ射线能量损失
分子式：
CAS号：
性质：又称δ射线能量损失。指次级电子(又称δ射线)在带电粒子轨迹附近一定范围内损失能量而形成径迹的作用机制。
CAS号：
性质：又称δ射线能量损失。指次级电子(又称δ射线)在带电粒子轨迹附近一定范围内损失能量而形成径迹的作用机制。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条