1) ultimate strength method
极限强度法
1.
Introduces calculation of fillet welding seal connections supported eccentric shear force on the basis of ultimate strength theory and deduces an applied design formula and compares ultimate strength method with elastic method through several examples.
通过算例比较了按极限强度法和按目前工程设计中常用的弹性方法计算的差别。
2.
This paper introduces calculation of bolt connectin supported by eccentric sheal force on the basis of ultimate strength and compares ultimate strength method with elastic method.
介绍了按极限强度法计算承受偏心剪力的普通螺栓连接计算方法 ,通过算例比较了按极限强度法和按目前工程设计中常用的弹性法计算的差别。
3.
The results indicate that ultimate strength method is more reasonable and economical.
介绍了按极限强度法计算偏心受剪螺栓群极限承载力的方法,采用极限强度法和弹性算法对一些实例进行比较,发现极限强度法较之弹性算法更加合理,也更方便工程中使用。
2) strength limit
强度极限
1.
The result of the experiment indicated that the strength limit and elastic modulus of the material can increase after annealing treatment within the temperature range, but at the same time, the material became crisp and its plasticity declined remarkably.
试验结果表明:在一定温度范围内退火处理可以大幅度提高该材料的强度极限和弹性模量,但同时使材料变脆,塑性显著下降。
3) Ultimate strength
强度极限
1.
Using thermal strength experiment to test and determine the pivotal parameters such as ultimate strength and thermal stress at the complicated condition of transient heating is very important for reliability estimation,life prediction of aerospace materials and security design of high-speed flight vehicle.
通过热强度试验,测试并确定航空航天材料在复杂高速热冲击条件下的强度极限等关键参数,对于航空航天材料和结构的可靠性评定、寿命预测以及高速飞行器的安全设计具有重要的意义。
4) ultimate strength
极限强度
1.
Investigation on the ultimate strength of unidirectional tapes and plain cloth hybrid laminates;
单向带/平纹布混杂铺层层合板极限强度研究
2.
Analysis of ultimate strength and sensitivity for oil tankers based on IACS common rules;
基于IACS共同规范的油船极限强度及敏感性分析
3.
Research development of ultimate strength of hull structure;
船体结构极限强度研究进展
5) ultimate stress
强度极限
1.
Both the tensile ultimate stresses and the relations between them are examined.
应用了高维分形理论 ,计算了颗粒复合材料CaCO3 ABS拉伸断口表面分形维数 ,测定了该种材料的拉伸强度极限 ,并对两者之间的关系进行了研
2.
In this paper,a two dimension variation method is applied to compute tensile fracture surface fractal dimensions of a grain composite material LDPE/CaCO 3,and set the relationship of tensile fracture surface fractal dimensions and tensile ultimate stress and material filler weight content percent.
应用计算断口表面分形维数的二维变差法，计算了颗粒复合材料ＬＤＰＥ／ＣａＣＯ３拉伸断口的分形维数，并且建立了断口分形维数与强度极限和填料颗粒含量之间的关系。
6) strength
[英][streŋθ] [美][strɛŋθ]
强度极限
1.
The failure problem of concrete bridge overlays in the system coupled by bridge deck and pavement for concrete highway bridges under vehicle loads was studied by utilizing the model in conjunction with the linear elastic fracture mechanics,and the strengths of new and original bridge overlays for an engineering example were obtained when the crack propagation occurred.
结果表明,新桥面铺装层(钢纤维增强混凝土)的强度极限明显高于旧桥面铺装层(普通混凝土)的强度极限。
补充资料：极限强度
分子式：
CAS号：
性质： 物体在外力作用下发生破坏时出现的最大应力，也可称为破坏强度或破坏应力。一般用标称应力来表示。根据应力种类的不同，可分为拉伸强度(σt)、压缩强度(σc)、剪切强度(σs)等。
CAS号：
性质： 物体在外力作用下发生破坏时出现的最大应力，也可称为破坏强度或破坏应力。一般用标称应力来表示。根据应力种类的不同，可分为拉伸强度(σt)、压缩强度(σc)、剪切强度(σs)等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条