1) charging and discharging
充放冷
1.
The models of charging and discharging of hold-over plate refrigerated vehicles were presented in this paper.
本文建立了冷板冷藏车的充放冷模型 ,对影响冷板充放冷的因素进行了分析 ,研究了不同种类、质量、过冷温度下共晶溶液的充放冷情况 ,指出可以根据需冷量对冷板进行部分充冷 ,既节约充冷量 ,又能保证冷板冷量得到充分利用 ;共晶冰过冷延长了充冷时间 ,增加了充冷能耗 ,而且降低了冷量的有效利用率。
2) charge-discharge
充放电
1.
The charge-discharge cycles showed that Ti-doped sample prepared at 600℃,spinels without doping sintered at 600 and 750℃,exhibited a initial capacity of 205,189 and 207mAh/g in the 1st 40-cycles,respectively.
充放电实验表明,在4。
2.
Screening battery from its charge-discharge characteristics is an unique trait peculiar to this system.
采用三级计算机控制方式、多功能电池夹具和模块化结构研制的二次电池检测系统,具有功能多、性能稳定和实用性强的特点,还独创了按充放电性能曲线分选电池的功能。
3.
During the charge-discharge cycles of amorphous (Mg_(60) Ni_(25))_(90)Nd_(10) alloy,NdMg_2 Ni_9 phase appears after four cycles and Mg_2 Ni phase appears after six cycles.
5) Nd_(10)在充放电循环中的组织演变。
3) constant current charge/discharge
恒流充放
1.
The electrochemical properties were tested by cyclic voltammetry and constant current charge/discharge.
循环伏安结果表明该材料具有良好的电容性能,用恒流充放电测得在1mA条件下,放电比电容可达290。
2.
The electrochemical properties were tested by cyclic voltammetry,AC impedance and constant current charge/discharge in threeelectrode system.
按m(MnO2)∶m(石墨)∶m(乙炔黑)∶m(羧甲基纤维素)∶m(聚四氟乙烯)=75∶10∶10∶3∶2制备电极材料,在电解液为c〔(NH4)2SO4〕=2mol/L的三电极体系中,通过循环伏安、交流阻抗和恒流充放电对其超级电容性能进行了考察。
4) cycle charge discharge
循环充放
1.
By testing the mechanic and electrochemical properties of lead and lead alloy,concluded that Pb Ca alloy have higher hardness and corrosion resistance,while Pb Sb alloy have better cycle charge discharger property than Pb Ca alloy.
通过对铅及其铅基合金的机械性能和电化学性能的测试可得,Pb-Ca系合金具有较高的硬度和较优良的耐腐蚀性能,而Pb-Sb合金的循环充放性能优于Pb-Ca合金。
5) charge and discharge
充放电
1.
New-type photovoltaic charge and discharge controller;
一种新型光伏发电充放电控制器
2.
Research of Li-ion Charge and Discharge System;
大功率锂离子蓄电池充放电系统的研究
3.
Investigation of Charge and Discharge for Battery Based on Techniques of Bidirectional Converter;
基于双向变流器技术的蓄电池充放电装置的研究
6) charging and discharging
充放电
1.
Analysised charging and discharging of lead-acetate battery;
浅析铅酸蓄电池的充放电过程
2.
Ship lead-acid battery charging and discharging;
船舶铅酸蓄电池与充放电
3.
The host computer is PC which can watch on the whole process of charging and discharging,data controlling,collecting and saving,and real-time displaying the wave form of every cell,and analyzing the data and output it as diagram etc.
该系统分为上位机和下位机2部分,上位机为普通PC机,可完成对电池充放电过程全面监测及数据采集的监控、存储,实时显示各只电池充放电波形,及时分析数据并以图表方式输出等;下位机由单片机结合CPLD构成主控单元完成电池充放电状态切换、电压电流数据的上传等功能。
参考词条
补充资料:充炭黑充油丁苯橡胶
分子式:
分子量:
CAS号:
性质:同时含有炭黑和油的丁苯橡胶。性能和用途与充炭黑丁苯橡胶和充油丁苯橡胶相似。由冷聚丁苯胶乳与炭黑的水分散液和油乳液经混合、凝聚、洗涤、过滤、干燥等步骤制得。
分子量:
CAS号:
性质:同时含有炭黑和油的丁苯橡胶。性能和用途与充炭黑丁苯橡胶和充油丁苯橡胶相似。由冷聚丁苯胶乳与炭黑的水分散液和油乳液经混合、凝聚、洗涤、过滤、干燥等步骤制得。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。