说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 微波高温烧结
1)  microwave high temperature (sintering
微波高温烧结
2)  microwave sintering
微波烧结
1.
Influence of microwave sintering on microstructures and properties of copper powder metallurgy material;
微波烧结对粉末冶金铜材显微组织与性能的影响
2.
Preparation of WC-10Co cemented carbide by microwave sintering;
微波烧结法制备WC-10Co硬质合金
3.
Research progress in microwave sintering technology;
微波烧结技术的研究进展
3)  high temperature sintering
高温烧结
1.
The post-processing of indirect SLS includes debinding, pre-sintering, high temperature sintering and metal infiltration.
间接法选择性激光烧结技术制备金属件的后处理工艺包括脱脂、预烧结、高温烧结以及渗金属。
2.
WC dispersion strengthened copper (DSC) was prepared by mechanical alloying (MA) in combination with high temperature sintering.
利用机械合金化与高温烧结方法制备WC弥散强化铜材料 ,研究了高温烧结温度和烧结时间对复合材料组织和性能的影响。
3.
Formation and influential factors of high temperature sintering in titanium sponge production by magnesium reduction method were analyzed.
论述了镁法海绵钛生产过程中高温烧结的形成及其影响因素,分析了减少高温烧结的控制措施。
4)  sintering ['sintəriŋ]
高温烧结
1.
Al_2O_3/Ti_xAl_y composite was produced by sintering TiO_2/Al bulk,which wasmade by squeeze casting.
采用挤压铸造法,先制备 TiO_2/Al 坯块,经随后高温烧结反应,可生成 Al_2O_3/Ti_xAl_y 复合材料。
5)  high-temperature sintering
高温烧结
1.
The hydroxyapatite coatings on the Ti6Al4V alloy are obtained by electrophoretic deposition process that contained the following steps-preparation of bioceramic suspension, electrophoretic deposition and high-temperature sintering.
经过制备稳定的悬浮液、电泳沉积、高温烧结等过程 ,在 Ti6 Al4 V合金上得到表面均匀的羟基磷灰石生物陶瓷涂层 。
2.
The results show that WCu10 contact materials manufactured by vacuum high-temperature sintering and infiltrating process have excellent properties and uniform and dense microstructu.
结果表明,用真空高温烧结及真空熔渗工艺制备出的WCu10触头材料具有良好的综合性能,其组织均匀、致密,氧、氮含量极低,符合真空开关的使用条件,并通过了真空负荷开关的型式试验。
3.
Aimed at preventing locally over-heating due to high-speed temperature raising in high-temperature sintering,the auto-control system for this kind of microwave oven is designed.
为了防止微波高温烧结过程中,升温十分迅速,发生局部过烧,用单片机设计高温烧结微波炉的自动控制系统。
6)  super high sintering temperature
超高温烧结
补充资料:陶瓷微波烧结


陶瓷微波烧结
mierowave sinteriflg of eeramies

陶瓷微波烧结mierowave sinteri眼of ceramiCs利用陶瓷及其复合材料在微波电磁场中的介电损耗,使其整体加热至烧结温度而实现致密化快速烧结。微波烧结技术最早出现于1976年。80年代中期以前,微波烧结仅限于容易吸收微波而烧结温度较低的陶瓷材料。1986年后,用微波烧结技术成功地烧结出Al 2 03、Zr()2、PZT、A儿03一TIC等陶瓷材料和陶瓷超导材料。微波装置功率也从数百瓦达到200千瓦,频率从915MHz达到60G玉12。 微波烧结的本质是微波电磁场与材料的相互作用,由高频交变电磁场引起陶瓷材料内部的自由或束缚电荷,如偶极子、离子和电子等的反复极化和剧烈运动,在分子间产生碰撞、摩擦和内耗,将微波能转变成热能,从而产生高温,达到烧结目的。 微波烧结具有以下特点:①极快的加热速度和烧结速度。传统烧结是通过外部热源的辐射及材料由表及里的热传导来加热的。微波烧结则是利用材料整体吸收微波能,在材料内部加热。由于这种独特的体内均匀加热机理,升温速度极快,一般可超过500℃/min,从而大大缩短烧结时间。②降低烧结温度。可以在低于常规烧结温度几百度情况下,烧结出与常规方法同样密度的制品。③改进材料的显微结构和宏观性能。由于烧结速度快,时间短,从而避免了陶瓷材料烧结过程晶粒的异常长大,有希望获得具有高强度、高韧性的超细晶粒的结构。例如常规方法烧结密度为99%的A1203,平均晶粒尺寸为8召m,而用微波烧结仅为0.8召m。④经济、简便地获得2000℃以上的超高温。在微波烧结中只有试样本身处于高温,因此整个装置紧凑、简单、低成本。⑤高效节能。节能效率可达50%左右。这是因为微波直接为材料吸收转化成热能,而烧结时间特别短。⑥无热惯性,便于实现烧结的瞬时升、降温自动控制。 (蔡杰)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条