说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 二工位冷挤压
1)  two_position cold extrusion
二工位冷挤压
1.
Relating with the experience and practices in the two_position cold extrusion technology for the oil cylinder and in the design of the die, cold extrusion, especially the superiority and the technological characteristics of two_position cold extrusion, was expounded.
结合油缸二工位冷挤压(光)工艺及模具设计实践 ,论述了冷挤压 ,特别是二工位冷挤压的优越性及工艺特点 ,并对该工艺及模具设计作了较详细的介绍 ,可供千斤顶行业及其它内孔要求较高的长筒形零件加工参考。
2)  cold extruding technology
冷挤压工艺
1.
After using the cold extruding technology, abained good effect.
采用冷挤压工艺取代传统的机械加工工艺,取得了较好的效果。
2.
the advantages of the titanium alloy hexagon locking-nuts with flange with cold extruding technology replacing hot extruding working method are introduced.
对钛合金六角法兰面自锁螺母进行了工艺分析、制订了冷挤压工艺路线、计算了毛坯尺寸及冷挤压力。
3.
The advantages of the reel internal gear with cold extruding technology replacing traditional metal cutting working method were narrated, and the technological for the reel internal gear was analyzed.
叙述了卷筒内齿轮用冷挤压工艺代替传统的金属切削加工方法的优点,并对卷筒内齿轮进行了工艺分析。
3)  cold extrusion
冷挤压工艺
1.
Optimizing aluminum alloy cold extrusion process;
铝合金冷挤压工艺的优化
4)  Cold extrusion process
冷挤压工艺
1.
Cold extrusion processing is complexity,and affected by many factors,which cause design difficulty.
冷挤压工艺特点复杂,影响工艺的因素多。
2.
The initial design of cold extrusion process and die was obtained by code retrieval.
冷挤压工艺复杂,影响因素多,造成冷挤压工艺设计难度大。
5)  cold extrusion process design
冷挤压工艺设计
1.
Research on mixed representation of domain isomeric knowledge in cold extrusion process design;
冷挤压工艺设计领域异构知识的混合表示
2.
Research on Cold Extrusion Process Design System and Its Key Technologies;
冷挤压工艺设计系统及其关键技术研究
6)  cold extrusion process planning
冷挤压工艺设计
1.
ANN-based knowledge auto-acquisition of cold extrusion process planning system;
基于人工神经网络的冷挤压工艺设计系统的知识自动获取研究
2.
Research on fuzzy-based cold extrusion process planning system and its key technologies;
基于模糊的冷挤压工艺设计专家系统关键技术研究
3.
The knowledge representation methods and fuzzy reasoning mechanism of a cold extrusion process planning system were researched.
研究了冷挤压工艺设计领域的知识表示以及冷挤压工艺设计系统的模糊推理机制。
补充资料:冷挤压


冷挤压
cold extrusion

  Iengliya冷挤压(eold extrusion)金属锭坯在回复温度以下进行的挤压,也称为冲击挤压。冷挤压设备一般采用机械压力机。冷挤压工具包括凸模、凹模,顶出器以及模架。常用的冷挤压方法有正向挤压、反向挤压和复合挤压,如图所示。冷挤压的时间极短,大约为0.1一0. 015。主要用于生产金属零件。 申目导 夔窿到夔夔匡夔黝夔巍巍 a bc 冷挤压的分类 a一正向挤压;b一反向挤压;。一复合挤压 冷挤压最初只限于铅和锡等软金属挤压,19世纪末开始应用于锌、紫铜、黄铜等比较硬的金属挤压。由于钢的变形抗力大,直至20世纪30年代出现磷化处理,使坯料表面形成润滑剂的吸附和支撑层,润滑得以强化之后,钢的冷挤压才取得进展。1945年以后,随着高强度模具材料的发展,冷挤压取得迅速发展。 毒黔贮赞呷冷挤压同热挤压相比较,产品的精度高,金属的变形抗力大。因此,对模具、铸坯的热处理、润滑等工艺条件都提出了特殊要求。高强度模具钢的允许单位挤压力一般可达到245oMPa。通常,冷挤压锭坯需经热处理,以软化金属和消除内应力,这关系到成品质量和模具寿命,甚至决定挤压的成败。钢材冷挤压时,一般采用表面磷化处理后再加充分润滑。岭噢黔牺雪 图3连续冷弯型钢设备布置图一开卷机;2一直头机;3一矫平机;4一剪头机;5一对焊机;6一辊道;7一引料辊;8一成形机; 9一高频焊机;10一整形机;n一飞剪(锯);12一集料装置
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条