说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 轴线误差
1)  Axis error
轴线误差
1.
Influence of axis error of gears with circular tooth profile on transmission precision;
圆弧齿轮副轴线误差对传动精度的影响
2)  axis straightness error
轴线直线度误差
1.
The virtual measuring instrument combines the technology to measure the form position error with virtual instrument to evaluate the axis straightness error by least square method and minimum zone estimation.
利用美国NI公司的LabWindows/CVI为软件开发平台,结合实验室现有的测量条件和基于PC的数据采集卡,开发研制了轴线直线度误差虚拟测量仪。
2.
According to the definition of axis straightness error,a mathematical model was developed to evaluate axis straightness error by way of least square method in the rectangular coordinates.
根据轴线直线度误差的定义 ,建立了在直角坐标采样时该项误差的最小二乘评定法数学模型 ,该模型的采样数据不需要等角度间隔采样 ;并用计算机进行仿真分析·结果表明 ,所建立的数学模型编程简单 ,计算出的轴线直线度误差值与真实情况的误差小于 10 -6μm·因此由本模型引入的误差可忽略不计·所建立的数学模型为研制形位误差虚拟测量系统提供了理论基础
3)  off-axis error
离轴误差(天线)
4)  axis intersection error
轴线不相交误差
5)  axial error
轴向误差
1.
To meet the requirement of 100% on-line inspection of gears in mass production in automotive and motorcycle industry, the two-flank principle is used to check the gear radial errors(thickness, radial composite error, run-out and error burs)and the gear axial errors(mean helix error, helix error and taper error)to realize the quick on-line inspection of gear machining flaws.
针对汽车、摩托车齿轮生产企业大批量齿轮生产现场,实现在线100%快速检测需要,本项目采用双面啮合原理测量齿轮的径向误差(齿厚、径向综合偏差、径向跳动、毛刺等)和轴向误差(平均齿向偏差、齿向偏差、锥度误差),实现齿轮的制造缺陷的现场快速检测。
2.
This paper, part seven of "Analysis of Errors and Inspection Groups on Hobbing Gear", dis- cusses the reason why the axial error occurs, the mathematical model and the relation between tol- erance group Ⅲ and axial error.
这部分的主要内容是论述轴向误差的产生原因,数学模型以及轴向误差与第Ⅲ公差组之间的关系。
3.
In this paper,the existing best-fit calculation,so as to the existence of axial RMS minimum goal for the design of the match,the current method of calculating the axial error is discussed,pointing out that some places a little unreasonable,a more accurate calculation of the axis to the formula for calculating the error and gives the derivation process.
针对现有的吻合计算,存在以轴向RMS最小为设计目标的吻合,对目前计算轴向误差的方法进行了讨论,指出了某些稍不合理的地方,提出了一个较为准确的计算轴向误差的计算公式,并给出了推导过程。
6)  Rotary axle center error
轴心误差
补充资料:DNA分子花窗(沿B―DNA轴线方向看)




DNA分子花窗(沿B―DNA轴线方向看)
  [图]图

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条