1)  image point
成像点
1.
The tossing process of Missile Bullets is complex and there are many optical image points.
子母弹多子弹抛射情况复杂,光学测量成像点多。
2)  spot diagrams of images
成像点图
3)  common imaging point gathers
共成像点道集
1.
Extraction and stack imaging of common imaging point gathers in angle domain.;
角度域共成像点道集的提取与叠加成像
4)  offset domain common image gathers
偏移距域共成像点道集
1.
In order to probe the relationships between wave equation offset domain common image gathers (ODCIGs)/angle domain common image gathers (ADCIGs) with migration velocity, we quantitatively derive the changes of ODCIGs and ADCIGs along with migration velocity on the assumption of uniform velocity medium with a horizontal reflector.
为了得到波动方程偏移距域共成像点道集(ODCIGs)和角度域共成像点道集(ADCIGs)与偏移速度的关系,在匀速单层水平反射情况下,对ODCIGs和ADCIGs随偏移速度的变化进行了定量的推导,得到偏移速度偏小时ODCIGs与半偏移距成双曲关系,反之成椭圆关系;结合深度聚焦分析,得到偏移速度偏大时,ADCIGs中视入射角大于真入射角,反之,小于真入射角;在速度偏小时,ADCIGs上剩余时差(RMO)与视入射角的正切值成椭圆关系,反之成双曲关系。
5)  angle domain common image gathers
角度域共成像点道集
1.
In order to probe the relationships between wave equation offset domain common image gathers (ODCIGs)/angle domain common image gathers (ADCIGs) with migration velocity, we quantitatively derive the changes of ODCIGs and ADCIGs along with migration velocity on the assumption of uniform velocity medium with a horizontal reflector.
为了得到波动方程偏移距域共成像点道集(ODCIGs)和角度域共成像点道集(ADCIGs)与偏移速度的关系,在匀速单层水平反射情况下,对ODCIGs和ADCIGs随偏移速度的变化进行了定量的推导,得到偏移速度偏小时ODCIGs与半偏移距成双曲关系,反之成椭圆关系;结合深度聚焦分析,得到偏移速度偏大时,ADCIGs中视入射角大于真入射角,反之,小于真入射角;在速度偏小时,ADCIGs上剩余时差(RMO)与视入射角的正切值成椭圆关系,反之成双曲关系。
6)  Time-shift angle domain common imaging gathers
时移角度域共成像点道集
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。