说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 温场测试
1)  temperature field measurement
温场测试
1.
Aimed to its difficulty, a useful method of vacuum-kiln s temperature field measurement is provided.
针对真空炉温场测试的特点进行了分析 ,推荐了合理的测试方法 ,并探讨了有关温场测试引用标准中的一些问题。
2)  Temperture field test
温度场测试
3)  Temperature measurement in large area
温场测量
4)  well temperature measuring
井温测试
5)  temperature measurement
温度测试
1.
In this paper the method of developing disturbed virtual instruments is introduced, and an example of disturbed temperature measurement system based on the TCP/UDP function in LABVIEW is given.
 介绍了利用LABVIEW建立分布式虚拟测试系统的方法与原理,并给出了利用LABVIEW中的TCP和UDP模块建立分布式温度测试系统的例子。
2.
A method which is applied to measure the surface temperature of the aeroengine rotor parts by using the thermoscope-piece to accomplish static state temperature measurement for a certain aeroengine compress rotor blade is introduced.
介绍了一种应用于航空发动机旋转件表面的温度测量方法 ,即使用测温片完成某航空发动机压气机转子叶片的稳态温度测试。
3.
the project coperated by Tongji University and SVW, the thesis puts forword the feasible optimai process scheme to improve the TIG welding of camshaft by the methods of computer simulation and temperature measurement,as well as the application of the.
本文运用计算机仿真和温度测试方法并结合传热学和材料学基本理论,提出改进凸轮轴重熔淬火硬化技术的具体工艺优化方案和技术改进措施。
6)  Temperature Measurement
测温试验
补充资料:测试结果可接受性的检查和最终测试结果的确定


测试结果可接受性的检查和最终测试结果的确定
check of the acceptability of test results and determination of the final test result

  C凡(3)二3.3d,时,取此3个结果的平均值作为最终侧试结果;否则取它们的中位数作为最终测试结果。。,为重复性标准差(即在重复性条件下所得侧试结果的标准差)。 在口田T 11792一1989中还对重复性和再现性条件下所得侧试结果可接受性的检查方法和最终测试结果的确定做了详细讨论和规定。(马毅林)ceshi 11叩uo kejieshCxjxing d6 iiancha he zuizhong ceshi】i闪旧de que心ing测试结果可接受性的检查和最终测试结果的确定(checkof山eac,ptability of test,ults助ddsterminationofthefi耐testresult)在商品检验中进行一次测试的情形不多见,当得到一个测试结果时,所得结果不可能直接与给定的重复性标准差作可接受性的检查。对测试结果的准确性有任何疑问时都应再进行一次测试。所以,对两个测试结果进行可接受性的检查是一般的情况。 可接受性的检查,实际上是一种统计检验。任何两个测试结果只要能通过可接受性的统计检验即可认为是一致的,均可接受。比如,在重复性条件下,所得结果之差的绝对值(下称绝对差)不超过相应的重复性限r(见重复性和再现性)的值,则认为两个结果是一致的,均可接受;如果两个侧试结果的绝对差超过r,则认为它们是不一致的,必须增加测试。 按国家标准《测试方法的精密度在重复性或再现性条件下所得测试结果可接受性的检查和最终测试结果的确定》(GBIT 1 1792一1989),在重复性条件下,如果两个测试结果的绝对差不超过r的值,可取两个侧试结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较低,须再做两次测试。当4个结果的极差(即其中的最大值与最小值之差)不超过相应的临界极差c,瓜(4)二3.6a,时,取4个结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较高时,只须再作一次测试。当3个结果的极差不超过相应的临界极差
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条