1) hydrophilic epoxy
亲水性环氧树脂
1.
In addition,a hydrophilic epoxy coating was used as exterior waterproofing.
广州(新)白云国际机场南航站楼轻轨站为地下两层结构,其防水方案为刚柔结合的结构自防水加PVC卷材、亲水性环氧树脂涂料外防水。
2) water-soluble epoxy resin
水溶性环氧树脂
1.
Crosslinking anionic emulsion was formed based on the emulsion and water-soluble epoxy resin.
采用种子聚合制备了丙烯酸系乳液,在此基础上配合水溶性环氧树脂,形成交联型阴离子乳液。
3) waterborne epoxy resin
水性环氧树脂
1.
Study and preparation of waterborne epoxy resin and its curing properties;
水性环氧树脂的研制及其固化性能研究
2.
Coating technics of waterborne epoxy resin flooring coatings applied to the building;
水性环氧树脂地坪漆在建筑物中的涂装工艺
3.
Study on performance of waterborne epoxy resin concrete;
水性环氧树脂混凝土性能研究
4) water-borne epoxy resin
水性环氧树脂
1.
Synthesis and properties of quaternary ammonium water-borne epoxy resin surfactants
季铵盐型水性环氧树脂乳化剂的制备及特性研究
2.
This paper summaries the advantages and disadvantages of aziridine cross-linked two-pack water-borne wood coatings,organosilicone coupling agent crosslinked ones,water-borne epoxy resin crosslinked ones and water dispersed isocyanate crosslinked ones; discusses the problems presented in the development of them from the aspects of application operabi.
文章概述了以氮丙啶交联型、有机硅偶联剂交联型、水性环氧树脂交联型、水分散型异氰酸酯交联型4类双组分水性木器涂料的优缺点,并从施工操作性、使用活化期及性价比3个方面探讨了其发展过程中存在的问题。
3.
The paper introduced the synthesis of water-borne curing agent of cashew nut shell liquid and water-borne epoxy resin emulsion with which the water-borne epoxy anti-corrosion rust tolerant primer-topcoat coatings were prepared.
分别介绍了水性腰果壳液固化剂与水性环氧树脂乳液的合成,并用此乳液与固化剂合成了水性环氧带锈防锈底面合一漆,讨论了乳化剂的添加量对乳液稳定性及涂膜硬度的影响,固化剂的添加量对漆膜性能的影响,最终确定了乳液与固化剂的最佳配比。
5) water emulsible epoxy resin
水乳性环氧树脂
6) water soluble epoxy resin
水溶性环氧树脂
1.
Soap-free emulsion copolymerization of acrylic acid series was prepared by seed-copolymerization, water soluble epoxy resin was compounded and cross linking anionic ring crush strengthening agent emulsion was formed under the catalysis of inorganic salt.
采用种子聚合制备了丙烯酸系无皂乳液,复配水溶性环氧树脂,在无机盐的催化下形成交联型阴离子环压强度增强剂乳液。
补充资料：二氧化双环戊二烯环氧树脂
分子式：
CAS号：
性质：又称R型环氧树脂。双环戊二烯的二氧化物。白色结晶粉末，分子量164.2，相对密度1.330，熔融温度≥185℃，环氧当量82。易溶于乙酸、醇、醚、酮、苯、四氯化碳等。固化物马丁耐热200℃以上，耐候性及电性能好，硬度高，有自熄性。缺点是冲击性能欠佳。由双环戊二烯与过醋酸反应而得。可铸塑、模塑和层合。主要用作耐热、耐候铸塑料、模塑料、玻璃钢、胶黏剂和涂料。
CAS号：
性质：又称R型环氧树脂。双环戊二烯的二氧化物。白色结晶粉末，分子量164.2，相对密度1.330，熔融温度≥185℃，环氧当量82。易溶于乙酸、醇、醚、酮、苯、四氯化碳等。固化物马丁耐热200℃以上，耐候性及电性能好，硬度高，有自熄性。缺点是冲击性能欠佳。由双环戊二烯与过醋酸反应而得。可铸塑、模塑和层合。主要用作耐热、耐候铸塑料、模塑料、玻璃钢、胶黏剂和涂料。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条