1) anti-compression and anti-bending strength
抗压/抗折强度
2) compressive and bending strength
抗压抗折强度
1.
In the condition of the fixed amounts of GBFS,steel slag,clinker and other admixture,the compressive and bending strength of the cementing materials drop obviously when the amounts of GXTLH is over 30%.
5%及水泥熟料23%时,矿渣掺量在12%~44%、钢渣掺量11%~44%之间制备的胶凝材料初凝时间、终凝时间、力学性能满足GB13592-92《钢渣矿渣水泥标准》;矿渣与钢渣比、水泥熟料及外加剂等掺量一定,GXTLH掺量超过30%时,GXTLH胶凝材料的抗压抗折强度均有所下降。
3) flexural and compressive strength
抗折抗压强度
1.
The influence of the fineness and the amount of the rubber powder on the flexural and compressive strength of cement mortar are researched.
探讨了废旧轮胎胶粉的细度和掺量对水泥砂浆抗折抗压强度的影响。
4) bending strength
抗折强度
1.
Expermental research on the influence of hair fibre on the bending strength of cement;
毛发纤维对水泥抗折强度影响的实验研究
2.
The effects of secret-water on cement concrete bending strength;
泌水对水泥混凝土抗折强度的影响
3.
On the basis of the damage and corrosion mechanism of the used tuyere sleeves of Baosteel,use the brown corundum and zircon power as the raw materials and study the thermal shock resistance,bending strength,compressing strength,porosity of Al2O3-ZrO2 for new sleeve.
在掌握了宝钢现有风口衬套破损原因和侵蚀机理的基础上,提出以棕刚玉和锆英石粉为主要原料,实验研究了新型风口衬套材质Al2O3-ZrO2的抗热震性、抗折强度、抗压强度、气孔率。
5) flexural strength
抗折强度
1.
Influence of process factors on the flexural strength of ZrO_(2(f))/PMMA-PMA composites;
工艺因素对ZrO_(2(f))/PMMA-PMA复合材料抗折强度的影响
2.
Study on the effect of steel fiber adding ways on concrete flexural strength;
钢纤维掺加方式对混凝土抗折强度影响研究
3.
Analysis on flexural strength in adhesive section of mortar with different strengths;
不同强度砂浆粘结面处抗折强度分析
6) folding strength
抗折强度
1.
Phase composition and microstructure of the composites were characterized by XRD and SEM,respectively,and the folding strength and compression strength were tested by universal testing machine.
力学性能测试结果表明,当掺入10%SiC(质量分数)时,材料的抗折强度最大,为58。
2.
The effects of five kinds of water-reducing agents: calcium lignosulfonate(CLS),modified calcium lignosulfonate(GCL1-6A),amino-sulfonic based superplasticizer(ASP),sulfonated naphthalene formaldehyde(FDN) and sulfonated melamine urea formaldehyde resin(SMUF) on the mechanical performances of mortar were studied,which include the compressive strength and folding strength.
研究了木素磺酸钙(CLS)、改性木素磺酸钙(GCL1-6A)、氨基磺酸甲醛缩合物(ASP)、萘磺酸甲醛缩合物(FDN)和三聚氰胺脲醛树脂(SMUF)5种减水剂对砂浆抗压强度和抗折强度的影响。
3.
On the basis of summarising of up the one\ s experience of the works, this article puts forwords to the design method of the mix proportion, which is the more practible method that folding strength be used for the design indice and describes some experience on the selection of the raw and processed materials.
在总结实践经验的基础上 ,文章提出较实用的以抗折强度为设计指标的配合比设计方法 ,介绍一些原材料的选用经
补充资料：抗剥强度
分子式：
分子量：
CAS号：
性质：见剥离强度。
分子量：
CAS号：
性质：见剥离强度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条