1)  ballast
压载体
1.
In light of the characteristics of the Yangtze River of deep water and swift current,and under consideration of the influences of dynamic water pressure on the stress of flexible mattress during sinking,this paper analyzes the stress on flexible mattress with concrete ballast,based on which,the calculation formulae for the stress on flexible mattress in different ways of laying are established.
针对长江水深流急的特点,考虑铺设过程中动水压力对软体排受力的影响,对系混凝土块压载体软体排在沉放过程中的受力情况进行分析。
2)  ballast
压载
1.
Adoption of Bend Upward Bulbous Bow to Improve Resistance Performance in Ballast Trial Condition;
用上翘型球首改善压载试航状态阻力性能
2.
The Research of Oil Marine Pollution & Protection and Ballast Monitoring System;
大型油船防污和压载监控系统研究
3.
Thispapertakesthebulkcarriersasanexampletoillustrateaspecificintroductionabouttheballastingpreparations, precautionsaswellastheproceduresofballast.
压载水管理是船舶关键性操作之一,对船体结构强度和安全航行具有重要意义,文章以散装船为例,着重介绍了卸货过程中压载作业的准备工作、预防措施和操作过程。
3)  ballast water
压载水
1.
Study on in-depth treatment of dirty ballast water from oil tankers by ozone oxidation;
应用臭氧氧化技术深度处理油船含油压载水的实验研究
2.
Pilotscale experiment of using hydroxyl radicle to kill tiny organism in ship ballast water;
羟基杀灭船舶压载水微小生物中试实验研究
3.
Risk assessment of ballast water with the application of standard additive model;
运用标准可加性模型对船舶压载水进行风险评价
4)  ballast tank
压载舱
1.
Painting technology of 14 210 m~3 liquefied natural gas tanker's ballast tank was introduced.
介绍了147210m~3液化天然气船压载舱涂装工艺,讨论了不同液化天然气船压载舱的涂装方案。
2.
In order to ensure ship safety,we must know the ship′s ballast tank pressure loss.
为了确保更换压载水时船舶的安全,设计船舶时必须对船舶压载舱压力损失进行计算。
5)  internal pressure load
内压载荷
1.
Numerical investigation and optimum design of complex thin-walled structures subject to internal pressure load;
内压载荷下复杂薄壁箱形结构数值模拟与优化设计
6)  ballast
压载舱
1.
This article introduces the preparation processand technical performances of environment-friendly long-lifesolvent-less pure epoxy ballast anticorrosion coatings.
介绍了对环境友好的长效无溶剂纯环氧压载舱防腐涂料的研制过程及其优良的技术性能,它可广泛地用于压载舱内壁的防护装饰。
2.
From the angle of stress, a basic mode of ballast distribution is proposed for floating structures of tidal power houses.
分析潮汐电站厂房浮运结构的计算荷载、计算工况、计算模型 ,并通过有限元分析 ,揭示了浮运结构的应力特点 ,以及影响浮运结构受力的因素 ,从结构受力角度提出了潮汐电站厂房浮运结构压载舱布置的基本模
参考词条
补充资料:压载水舱漆
分子式:
CAS号:

性质:用于船舶的各种压载水舱、艏尖舱、艉尖舱、船底水舱等部位的涂料。这些水舱的腐蚀环境恶劣,长期处于海水压载和空载的干湿交替状态,环境湿热,盐分高又不通风,要求涂料有优良的耐水、耐盐雾、耐干湿交替和抗腐蚀性能,同时要求其一次成膜有较高的膜厚,以保证长的使用寿命,一般5年后锈蚀面积小于5%。常采用厚膜型环氧沥青、乙烯沥青、氯化橡胶沥青、异氰酸酯焦油环氧、无溶剂环氧沥青涂料等。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。