说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 时变模型
1)  time-varying model
时变模型
1.
Safety monitoring time-varying model of concrete dam′s deformation;
混凝土坝变形安全监控时变模型
2.
In this article,the improved fuzzy neural network with time-varying model in fitting and forecasting of the horizontal displacement monitoring of one dam is used,and the BP model is the comparative example.
针对时变监控模型比常规监控模型更有效且能准确进行变量分离,通过改进的模糊神经网络(IFNN)结合时变模型对陈村水库大坝的水平位移进行拟合与预测,并与BP模型做了比较。
3.
By the reasonable assumption and deductive derivation the logical hydraulic concrete compressive strength time-varying model was established and the existing info.
Bolomey水灰比—强度模型、Powers凝胶—孔隙比强度模型、Francois de larrard双曲线强度模型等,并分析了各抗压强度时变模型的优缺点,提出了对抗压强度模型进行改进的思路。
2)  time vary ARMA model
时变ARMA模型
3)  time-varying ARFIMA model
时变ARFIMA模型
1.
This paper builds a time-varying ARFIMA model of the time series of Taiwan Dollar.
然后对新台币汇率时间序列建立时变ARFIMA模型。
4)  time-varying AR model
时变AB模型
5)  time-varying parameter model
时变参数模型
1.
Medium and long-term load forecasting based on time-varying parameter model
基于时变参数模型的中长期负荷预测
2.
A time-varying parameter model is established to analyze the nonstationary random vibration signal(NSRVS) of a spacecraft in a certain time period.
采用时变参数模型对航天器某时段非平稳随机振动信号(NSRVS)进行建模分析,利用过程神经元网络(PNN)求解模型的时变参数并以此确定信号的时变自功率谱密度。
3.
This paper uses time-varying parameter model and panel data model to analyze the effects of the active fiscal policy on total factor productivity of national economy and provincial economy in China.
利用时变参数模型和面板数据模型,可以对积极财政政策的全要素生产率增长效应进行分析。
6)  time-varying autoregressive model
时变自回归模型
1.
In this paper,an algorithm of normalized parametric adaptive matched filter based on time-varying autoregressive model is introduced.
文中介绍了一种基于时变自回归模型的归一化参数自适应匹配滤波算法。
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条