说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 侧边曲线方程
1)  the side curve equation
侧边曲线方程
2)  lateral displacement curve equation
侧移曲线方程
1.
Based on the experimental study and Timoshenko\'s shear beam theory,and considering elastic constant value and the construction feature of the multi-ribbed composite wall,the lateral displacement curve equation of the multi-ribbed composite wall is established,which is contained shear deformation.
在试验研究基础上,依据铁木辛柯剪切梁理论并考虑密肋墙体弹性常数取值和构造特点,建立了包含剪切变形在内的密肋复合墙侧移曲线方程;同匀质混凝土墙侧移方程相比,密肋墙侧移方程中的弹性常数是与墙体构造有关的变参数表达式。
3)  side curve
侧边曲线
4)  two-sided piecewise curve boundary
双侧曲线边界
5)  curve equation
曲线方程
1.
Study on curve equation of unfolded-drawing on the cut-cone surface
截头圆锥体表面交线展开图曲线方程的研究
2.
The curve equations of stereographic projections for meridian and woof in Wulff net are worked out with mathematical method.
 运用数学方法推导出了乌氏网极射平面投影经线和纬线的曲线方程,并在此基础上,介绍了一种利用计算机精确绘制任意经度和纬度乌氏网的方法。
3.
The curve equation of the developed pattern of the arciform plate is presented.
介绍了塔器内梁型气体喷射式填料支承及其拱形板展开图 ,并通过详细计算给出了该展开图的曲线方程。
6)  curvilinear equation
曲线方程
1.
In this paper, the curvilinear equation of the complexometric back titration has been derived, the complexometric back titration curve has been drawn and the pN break has been calculated.
推导了络合返滴定曲线方程 ,绘制了络合返滴定曲线和计算了pN突跃。
2.
Here we obtain the complete ration geometrical characteristic of the curvilinear equation in plane by using translation and rotation of axes,therefore we can show the important parameter of the curve expressed as their idiographic equation conveniently.
文章用坐标平移与旋转方法,获得了曲线方程(a1x+b1y+c1)(a2x+b2y+c2)=1((a12+b12)(a22+b22)≠0(1)在xoy平面上的完全定量几何特征。
3.
With the methods of fitting,interpolation,etc,a curvilinear equation which can conveniently and quickly describes the bending centerline has been obtained.
以条材类零件受到集中力作用产生的弯曲中心线为研究对象,通过拟合、插值等方法,分析得出一种方便、快捷描述弯曲中心线的曲线方程。
补充资料:方程式曲线在UG软件中的生成 Unigraphics-二次开发

新闻摘要:在UG软件中,对于曲线的生成有多种生成工具,可生成直线、圆弧、椭圆、样 条、抛物线、双曲线等等,特别值得一提的是,在UG软件中,具有生成以方程 式表达的曲线的功能,且该曲线还具有相关性,即如果方程式变化时,曲线也 会跟着变化,这特别适合某些特定的需要,如凸轮的建模等。 在UG软件中方程式曲线的建模步骤主要由两在UG软件中,对于曲线的生成有多种生成工具,可生成直线、圆弧、椭圆、样 条、抛物线、双曲线等等,特别值得一提的是,在UG软件中,具有生成以方程 式表达的曲线的功能,且该曲线还具有相关性,即如果方程式变化时,曲线也 会跟着变化,这特别适合某些特定的需要,如凸轮的建模等。


     在UG软件中方程式曲线的建模步骤主要由两步构成:第一步是建立表达式,第 二步是建立该方程式曲线,下面以一实例为例,说明其建立步骤。


     下图是一凸轮曲线的展开图,其方程式是: y=30sinα+40 0≤α≤360


 


     第一步是将以上方程转换为参数方程 x=35*cos(α) 35为外圆半径 y=35*sin(α) z=30*sin(α)+40 α=360*t 0≤t≤1


     注意:将方程转化为参数方程时,一定要将其转换为以变量t为参数的方程,在 UG中,t的变化范围一定是从0到1。


     第二步,将参数方程输入为UG软件中的表达式,对应以上参数方程,请输入以 下表达式: t=1 α=360*t x=35*cos(α) y=35*sin(α) z=30*sin(α)+40


    第三步建立曲线:     Toolbox->Curve…->Law Curve->提示定义X轴->选By Equation->提示定义X轴,输入参数表达式->输入t->提示定义X轴,输入方程表达式->输入 x->接着提示定义Y轴,同样按照步骤定义Y轴和Z轴->选择OK,生成所需曲线。


     第四步建立实体模型,用UG软件的其他功能,完成最终模型。


 

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条