1) CO2 working medium
CO2工作介质
2) actuating medium
工作介质
1.
Over seventy percent of the reasons that lead to the fault are the actuating medium of hydraulic system.
冶金机械设备液压系统故障的原因较多,由液压系统工作介质因素导致的故障约占70%以上,而工作介质热因素是其中之一,已得到人们的重视。
2.
This paper analyzes the influence of bulk modulus of actuating medium on the pressure in a hydraulically driving system.
本文分析液压传动系统中工作介质对系统内压力瞬变的影响。
3) cooling liquid
工作介质
1.
In the paper,the research about wire wasting regularity affected by cooling liquid are given by using the typical cooling liquid,and a new concept that is durable characteristic of electrode wire is delivered.
通过3种典型工作介质的使用,研究了工作介质对电极丝损耗的影响规律,并提出了电极丝使用耐用度的概念,分析了工作介质洗涤性能改善对电极丝耐用度提高的原因,提出了机床电极丝导向、喷水冷却结构的改进方案。
2.
In the paper,the analysis are given about the cutting gap and the discharge feature of gap through using and comparing the different typical cooling liquid basing on collecting discharge waveform.
对高速走丝电火花线切割加工放电机理进行了探讨,根据不同工作介质下的典型放电波形分析了极间放电特征,结合分析和工艺试验指出:工作介质洗涤能力的改善对加工工艺指标的提高起到关键性的作用。
4) working medium
工作介质
1.
This paper analyzed the flow of working medium in extrusion by an athletic differential equation of viscous fluid and discussed the influence of the viscosity on Hot Hydrostatic Extrusion(HHE).
采用粘性流体的运动微分方程分析工作介质在锥模中的挤压流动,通过分析工作介质的粘度对热静液挤压的影响,指出了合理的选择工作介质的成分使得粘度适宜,可以使热静液挤压力最小,而且能够避免挤压件缺陷的产生。
2.
Workpiece of YG8 was multiply cut in the test by adopting displacement restrictor of bar and constant tension device to improve the electrode-wire\'s space stability, and choosing composite cooling liquid as working medium in the former two cutting and kerosene in the final finish cutting.
通过采用限位棒、恒张力装置提高电极丝的空间稳定性,并在前两次切割采用复合工作液最后精修采用煤油作为工作介质对硬质合金YG8进行了多次切割。
3.
In this paper,the working principle of the heat-pipe was introduced,the designed heat-pipe exchanger and its application over the years was described,focused on the requirements of the working medium of the heat-pipe the working medium,and the current several commonly used medium was analyzed.
本文对热管的工作原理做了介绍,叙述了多年来设计的热管换热器及其应用情况,重点阐述了热管对其工作介质的要求和对目前常用的几种工作介质进行了分析研究。
5) actuating medium
工作介质，工质
6) thermodynamic medium
热工作介质
补充资料：poly(bisphenol a-co-4-nitrophthalic anhy-dride-co
CAS：61128-46-9
分子式：(C31H20O8·C6H8N2)x
中文名称：5,5'-[(1-甲基亚乙基)双(4,1-亚苯氧基)]双-1,3-异苯并呋喃二酮与1,3-亚苯二胺的聚合物
英文名称：1,3-Isobenzofurandione, 5,5'-[(1-methylethylidene)bis(4,1-phenyleneoxy)]bis-, polymer with 1,3-benzenediamine
3-isobenzofurandione, 5,5'-[(1-methylethylidene)bis(4,1-phenyleneoxy)]bis- polymer with 1,3-benzenediamine
poly(bisphenol a-co-4-nitrophthalic anhy-dride-co
1,3-Isobenzofurandione,5,5'-[(1-methylethylidene)bis(4,1-phenyleneoxy)]bis-,polymer with 1,3-benzenediamine
分子式：(C31H20O8·C6H8N2)x
中文名称：5,5'-[(1-甲基亚乙基)双(4,1-亚苯氧基)]双-1,3-异苯并呋喃二酮与1,3-亚苯二胺的聚合物
英文名称：1,3-Isobenzofurandione, 5,5'-[(1-methylethylidene)bis(4,1-phenyleneoxy)]bis-, polymer with 1,3-benzenediamine
3-isobenzofurandione, 5,5'-[(1-methylethylidene)bis(4,1-phenyleneoxy)]bis- polymer with 1,3-benzenediamine
poly(bisphenol a-co-4-nitrophthalic anhy-dride-co
1,3-Isobenzofurandione,5,5'-[(1-methylethylidene)bis(4,1-phenyleneoxy)]bis-,polymer with 1,3-benzenediamine
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条