说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 杂质尺寸
1)  impurity size
杂质尺寸
1.
The determination of the maximum permissible impurity size in HV XLPE cable insulation is of importance in ensuring its longterm ageing characteristics.
电树枝是影响XLPE电缆长期老化性能的重要因素,而确定高压XLPE电缆绝缘层中允许的最大杂质尺寸对于保证其长期老化性能是很重要的。
2)  media size
介质尺寸
1.
Research on the methods of selecting the optimum media size for single size feed;
窄级别给料球磨机最佳介质尺寸判据研究
2.
The result shows that reducing the grinding media size properly can increase the grinding efficiency and improve the quality of grinding products.
针对百花岭选矿厂实施降低碎矿粒度改造工程后入磨粒度组成变细的现状,对磨矿介质的适宜添加尺寸进行了理论计算与分析,并进行了介质尺寸的工业试验,试验结果表明,伴随入磨粒度的降低,适当减小介质尺寸可有效地提高磨矿效率,改善磨矿产品质量。
3)  dimensional quality
尺寸质量
4)  inclusion size
夹杂物尺寸
1.
Further investigation revealed that this difference is mainly caused by the difference in inclusion size.
结果表明,虽然实验料的氧含量相同,但由于钢中夹杂物尺寸的差异,使其高周疲劳性能存在明显差异。
2.
The mechanism of ultra high cycles fatigue fracture of high strength steel,especially the effect of inclusion size on fatigue life,were investigated.
为提高工程结构用钢的使用寿命,研究了高强度廉价耐候钢,特别是Mn-Cu细-晶,PR-E-超细晶的协同作用和超低碳贝氏体组织对钢耐蚀性的影响;为提高机械制造用钢的使用寿命,研究了高强度钢的超高周疲劳断裂机制,特别是夹杂物尺寸对钢疲劳性能的影响;为提高合金结构钢的质量研究了微米级夹杂物的形成理论和控制技术。
5)  high quality and large size
优质大尺寸
1.
The research progress and the main problems to develop high quality and large size laser crystals in china are described.
文章综述了国内外大尺寸Nd∶YAG,Nd∶GGG,Yb∶YAG晶体的发展概况,指出了我国优质大尺寸激光晶体研究进展及主要差距,展望了发展前景。
6)  critical inclusion size
临界夹杂物尺寸
1.
The critical inclusion sizes (CIS) of some steels with given matrix hardness or tensile strength and surface roughness under high cycle fatigue condition were estimated mainly on the basis of Murakami's theory, i.
依据Murakami的“夹杂物等效投影面积模型”估算了在高周疲劳条件下一定硬度(或强度)高强钢的“临界夹杂物尺寸:。
补充资料:工程图标准尺寸及坐标尺寸

标准标注类型,是我们常用的标注类型。而坐标标注是便于数控加工采用的另一中标注形式。PRO/E可以将两种标注方式进行转换。


· 3.2 标准标注到坐标标注的转换


注意: 转化为坐标标注的尺寸必须是线性标注的,下列尺寸不能转化为坐标标注:


 



  • 被显示成线性尺寸的直径
  • 中心线尺寸

 



  1. 选择MODIFY DRAW > Dim Params > Dim Type > Ordinate Dim > Create Base.
  2. 选择作为参考基准线的尺寸
  3. 选择基准的引出线,该点为0点
  4. 选择 MOD DIM TYPE > Lin to Ord .
  5. 选择线性尺寸:注意:必须选择具有相同基准的尺寸

========>>>>

· 3.3 由坐标标注到标准标注的转化

1. 选择 DIM PARAMS > Diam Dim Type .


2.点击Ord to Lin


3.选择尺寸即可

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条