1) silane corss linking agent
硅烷交联料
2) silane cross linked mother batch
硅烷交联母料
3) silane crosslinking
硅烷交联
1.
The effects of silane crosslinking and peroxide crosslinking on the crystallization behaviors and the mechanical properties of crosslinked ultra-high molecular weight polyethylene (UHMWPE) were studied.
研究了硅烷交联和过氧化物交联对超高分子量聚乙烯结晶结构及力学性能的影响。
2.
The technology of silane crosslinking is the main method for producing crosslinked polyethylene pipes.
硅烷交联法是制造交联聚乙烯管材的主要方法。
3.
The silane crosslinking HOPE material was developed by two - step method.
采用两步法研制了硅烷交联HDPE,利用二次正交回归设计探讨了交联温度、交联时间等5个因素对硅烷交联HDPE的拉伸强度、断裂伸长率及凝胶含量的影响,并对所得的回归方程进行了最优化,找出了各单项性能最优时和综合性能最佳时所对应的参变量值,并通过实验进行了验证。
4) Silane cross-linking
硅烷交联
1.
Value analysis of investment on cables made by the two step silane cross-linking method;
二步法硅烷交联电缆的投资价值分析
5) Silane Crosslinked
硅烷交联
1.
Development of Silane Crosslinked and LSOH Flame retardancy polyolefine;
硅烷交联低烟无卤阻燃聚烯烃的研制
2.
In thes paper with the orthogonal design the formulation of silane crosslinked LDPE was discussed and the influenes of warm water crosslinking time on properties were found out.
本文用正交设计法探讨了硅烷交联低密度聚乙烯（XLDPE）的配方设计，以及温水交联时间对性能的影响。
3.
The thermal and mechanical properties of silane crosslinked LLDPE(SXLLDPE) were investigated through thermogravimetric analysis(TGA),differential scanning calorimetry(DSC),Vicat softening point measurements and mechanical tests.
通过热重分析(TG)、差示扫描量热分析(DSC)、维卡软化点测定及拉伸性能测试等手段研究了稀土化合物硬脂酸镧对硅烷交联线性低密度聚乙烯LLDPE(SXLLDPE)性能的影响。
6) Silane cross linking
硅烷交联
1.
A method by heat moulding to repair the insulation defect of the Si XLPE cable after insulation extrusion and before silane cross linking is presented, by using which the expected requirements may be satisfied, i.
本文介绍硅烷交联聚乙烯电缆绝缘缺陷 ,在绝缘挤出之后与温水交联之间采用热压模方法修补 ,可达到预期效果 ,即绝缘电性能及热老化性能均能满足使用要求。
补充资料：Tm-002硅烷交联剂
1. 化学名称
甲基三乙酰氧基硅烷
2. 物理性质
无色至浅黄色透明液体，较低温度下可转变为白色晶体。易吸湿，可溶于醋酸酐，遇水会交联，并产生醋酸。
3. 技术规格
外观 无色至浅黄色透明液体，或白色晶体
密度（r25）g/cm3 1.1750~ 1.1800g/cm3
含量（%） ≥95
折射率(n 25d) 1.4050±0.0005
沸点（℃） 110-112/17mmhg
熔点（℃） 40.5
cl-（%） ≤0.1
4. 用途
本品主要用作室温硫化硅橡胶的交联剂。
5. 包装与储运
塑料桶包装，每桶净重10kg、25kg、100kg、180kg。密封储存于阴凉、干燥通风处，防潮防水，远离火种、热源。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条