说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> GPS点高程
1)  Altitudes of GPS Points
GPS点高程
1.
The Decision Methods of the Altitudes of GPS Points;
GPS点高程的确定方法
2)  GPS height
GPS高程
1.
Research of influence and correction of GPS antenna phase center deviation on GPS height;
GPS天线相位中心偏差对GPS高程的影响及改正研究
2.
The application of support vector machine method in GPS height transformation;
支持向量机方法在GPS高程转换中的应用
3.
Converting GPS height by a new method based on neural networks;
基于神经网络的转换GPS高程的新方法(英文)
3)  GPS Altitude
GPS高程
1.
The multi-aspect function application in GPS altitude fitting;
多面函数在GPS高程拟合中的应用
2.
The optimum selection of GPS altitude fitting model
GPS高程拟合模型的最优选择
4)  GPS elevation
GPS高程
1.
Reasearch on Increasing GPS Elevation Accuracy;
提高GPS高程方向精度的研究
2.
By combining semiparametric survey adjustment Models with the least squares collocation to deal with GPS elevation, the calculation method of a positively definite regularity matrix is deduced and the corresponding results are obtained.
利用罚最小二乘原理构造加权惩罚平方和,将半参数回归模型与最小二乘配置结合起来,来处理GPS高程问题,导出了配置型模型中正规化矩阵正定时参数平差的计算方法,用直接法得到了参数和信号的估计量,给出了相应的公式。
5)  GPS height network
GPS高程网
1.
This paper research the design and establishment of all kinds of GPS networks systematically and discusses the design, field observation and implementation of the GPS control network with high accuracy, GPS engineering control network, special GPS control network, and the GPS height network.
本文全面系统地研究了GPS各种控制网的布设,探讨了高精度GPS控制网、GPS工程网、特殊GPS控制网及GPS高程网的设计方法,野外观测方案及实施方法。
6)  GPS height anomaly
GPS高程异常
1.
A vast amount of GPS survey data make known that the GPS height anomaly variations is evenly and echelon in parts of an area.
大量的 GPS测绘资料表明 ,小范围内 (局地 ) GPS高程异常呈现出一种均匀梯次变化特点 ,根据局地 GPS高程异常均匀梯次变化的几何特征 ,总结出了局地 GPS高程异常均匀梯次变化的数学模型。
2.
On the basis of the GPS height survey results in many provincial administrative regions of China, using interpolation and extrapolation methods, the GPS height anomaly map of China has been drawn up, which possesses certain applicable value.
该文以国内许多省级行政区内的GPS测高成果为基础 ,用外推或内推的方法 ,绘制出了我国的GPS高程异常图 ,有一定的应用价
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条