说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 电流注入控制
1)  current injection control
电流注入控制
2)  inection current control
注入电流控制
3)  current injection phase shifted control
电流注入移相控制
4)  injection controlling
注入控制
1.
The beam quality of an unstable resonator copper vapor laser with injection controlling has been studied experimently.
实验研究了注入控制对铜蒸气激光非稳腔输出光束质量的影响,从输出光发散角时间分辨过程的测量结果说明注入光加速了被注入腔内激光发散角的减小过程。
5)  injection current
注入电流
1.
Theoretical analysis and characterization of injection current distribution and influences on optical near-field modes in gain-guided vertical-cavity surface-emitting lasers;
增益导波垂直腔激光器注入电流空间分布及其对激光近场模式影响的理论分析和表征
2.
After the node sequence injection current is got,considering the influence from other sequence components,the following solution is applied:for positive and negative sequence problems ,node voltage is solved by for/backward sweep method;for zero sequence problem,node voltage is.
在求得各序间相互影响各序节点注入电流之后,采取以下求解方法:对正序、负序网络沿辐射支路用前推回代的方法求解,对零序网用常规高斯塞德尔(Gauss-Seidel)迭代法求解,这样可加快求解的速度。
3.
This paper proposes an injection current based three phase power flow method.
提出了节点注入电流的三相潮流分析方法。
6)  current injection
电流注入
1.
This paper introduces the method to achieve time association in current injection experimentation.
本文介绍了在电流注入试验中实现时间关联的方法,并采用该方法得到了典型电路失效概率分布。
2.
In this paper,the EMP failure modes of solid state relays were obtained by current injection method.
本文通过电流注入法对某型直流固态继电器输入端与输出端的电磁脉冲损伤机制进行了实验研究,确定了两种失效模式。
3.
The electromagnetic pulse(EMP) damage mechanism and failure modes are obtained for the input port and output port of solid state relays by current injection method.
采用电流注入法对某型直流固态继电器输入端与输出端的电磁脉冲损伤机制及失效模式进行了实验研究,结果表明:输入端注入电磁脉冲信号时,输出端会产生误动作,并可造成输入电路中三极管BE节产生短路损伤,导致输入端施加控制信号时输出端无法导通;输出端注入电磁脉冲信号时,可造成输出电路中MOSFET管的栅极和漏极产生短路损伤,导致输出端短路。
补充资料:控制电流法
分子式:
CAS号:

性质:利用恒电流仪或经典恒电流线路来控制工作电极的电流密度,使其依次恒定在不同的数值,测定相应的稳定电极电势或电势随时间的变化。前者得到的电流-电势关系,即稳态的极化曲线。后者得到电势随时间的变化,称为计时电势法。电流的改变可用手动逐点调节,也可用阶梯波信号控制恒电流仪来实现,故也称电流阶跃法。该法优点是仪器简单;问题是充电电流不易补偿。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条