说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 旋转模态
1)  revolving mode
旋转模态
1.
In this paper,the operating principle of ultrasonic motor using revolving mode in plane is presented.
阐述了面内旋转模态超声波电机的工作原理 ,针对面内旋转模态电机的特点 ,分别从陶瓷片的极化、工作界面的确定、振动模态的选择、定子的固定方式、预紧机构的设计几方面论述了电机设计过程中应当注意的问题。
2)  rotational isomeric state model
旋转异构态模型
1.
In this paper,we have calculated intrinsic energy, free energy and entropy of the unperturbed polysilane chain by using the rotational isomeric state model and the second order interaction approximation.
采用旋转异构态模型和二级相互作用近似,计算了无扰Polysilane链的内能、自由能和熵,讨论了它们与链长和温度的关
3)  circumrotation condition
旋转状态
4)  dynamic rotary
动态旋转
5)  rotational molding
旋转模塑
1.
Study on High-speed Rotational Molding Processing of Glass Fiber Reinforced Polyester Pipe;
玻璃钢管的高速旋转模塑成型工艺研究
2.
Study on pigmentation of field medical chest by rotational molding;
野战医疗箱旋转模塑工艺条件下着色研究
3.
It was suggested that in the rotational molding, the initial viscosity controlled the wall thickness of the product and the gel rate controlled the uniformity of the wall thickness.
应用正交实验方法研究了引发剂、促进剂及二氧化硅(SiO2)粉末的加入量对旋转模塑成型制品壁厚和壁厚均匀程度的影响,测定了不同配比黏度变化曲线,找出了树脂体系黏度变化对成型制品质量的影响规律。
6)  Rotational moulding
旋转模塑
1.
A new process of the rotational moulding process for 3-D braiding was designed.
开发设计了三维编织旋转模塑新工艺,以三维编织圆管为增强材料、TDE-85环氧树脂为基体,对其成型工艺进行了设计,初步讨论了模具结构、加热时间、旋转速度、主次轴转速比、树脂加料量、树脂的浸润等因素在工艺中的作用。
2.
The number of advantages which includes low level of residual stresses, low product cost, being suitable to produce large hollow plastic production offered by this process over other plastic processing methods makes rotational moulding lots of engineering sense.
旋转模塑是一种以塑料粉末为原料成型中空塑料制品的工艺。
补充资料:管材旋转模冷拔


管材旋转模冷拔
cold drawing of tube through revolving die

的主动旋转外模与顶头(或芯棒)之间拔制管材的工艺(见图)采用旋转模拉拔,拉拔的部分变形为滚轧所取代,滚珠或滚柱与管材接触表面之间为滚动摩擦。摩擦系数小,可以降低拔制力。这对薄壁管和低塑性材料的拉拔很有利。但是,旋转模冷拔管材存在以下的缺点:(1)旋转槽内滚珠或滚柱的咬入角较小(镇15。),睿二瑙 滚珠式旋转模的结构及拔管过程 l一端支持环;2一安装在旋转支持器内的模套; 3一管材;4一芯棒guaneai xuanzhuanmu lengba管材旋转模冷拔(eold arawing of:ub。thro-u只h revolving die)室温下在装有滚珠或渡杜使得每转的减壁量不能取大,一般小于滚珠或滚柱直径的2%;(2)为防止管体表面出现螺旋线,旋转模每转动一次管材的轴向送进量必须很小,对于滚珠组装的旋转模,约为管材周长的2%一4%;(3)模内相互接触的滚珠或滚柱体之间以及它们与模套之间摩擦能耗的比重也很大。由于上述原因,旋转模冷拔管材未能在大生产中广泛应用。 (周忠民)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条