1)  contact mode
接触型式
1.
The contact modes of sliding joint is developed.
文中给出了移动副的各种接触类型,并运用力学分析的方法得出了各种接触型式的存在条件和摩擦力计算公式。
2)  Contact
接触
1.
Check ring joint structure design in underwater skirt pile gripper based on body contact nonlinear finite element analysis;
基于接触的水下夹桩器卡环连接结构设计
2.
Dynamic simulation of the contact between drill stem and well wall;
钻柱与井壁接触的动态仿真分析
3.
Contact Nonlinear Finite Element Analysis on the Pressing Block Tooth in Underwater Skirt Pile Gripper;
基于接触的水下夹桩器压块齿非线性有限元分析
3)  contacting
接触
1.
In addition, the contacting problem of plates was analyzed in this paper by using the penalty method, the contacting force of plates was derived, and the new methods for searching crateria were proposed.
利用罚函数方法 ,对板材自身接触问题进行分析 ,给出了接触板材间的接触力 ,并提出一种接触搜索判断方法 ,同时给出了算
2.
In order to solve the contact problem of different parts of the blank, a new algorithm for contacting judgment is proposed.
对 SPF/DB加工过程中板材的动态扩散连接问题进行了分析 ,该过程属于有限元分析中粘着式接触问题 ,并提出了新的接触判断方法 ,同时采用 Mindlin壳元 ,对非对称双室盒形件的 SPF/DB过程进行了模
4)  contact problem
接触
1.
Non-Hertz contact problems are studied according to multi-level multi-integration,and are computed with program.
首次采用多重网格积分(MLM I)理论,对非Hertz接触问题进行了详细研究,并编写了相应的计算程序。
2.
The contact element method and original stress method were used to analyze the elastic plastic contact problem of wheel/rail with measured surface micro roughness.
采用接触单元方法 ,结合初应力法 ,采用测量获得的表面微观粗糙度 ,对轮轨弹塑性接触问题进行了研究 ,获得了轮轨的表面接触压力分布等结果。
5)  touch
接触
1.
Stack and juxtaposion make architectures lose lots of their breathing touch surfaces.
并置和层叠使建筑损失了呼吸的接触面,这种无隙、高度实体化的建筑导致的封闭体系,是造成内部使用者与自然隔离的根源。
2.
The locations touched between the mother and the young are mainly the areas of head,etc.
母幼间接触的部位主要是头部等感官较敏感区域 ,通过各种接触是建立母幼友好、亲昵关系的主要途径。
6)  Contact non-contact
接触非接触
参考词条
补充资料:55°圆锥管螺纹型式和尺寸
螺纹代号
基本尺寸
英 寸
大径
mm
d=D
螺距
mm
p
每英寸牙数
tpi
中径
mm
d2=D2
小径
外螺纹
d3
牙型高度
H1
圆弧尺寸
r
底孔尺寸
mm
R 1/161/16"7.7230.907287.1426.5610.5810.1256.4
R 1/81/8"9.7280.907289.1478.5660.5810.1258.4
R 1/41/4"13.1571.3371912.30111.4450.8560.18411.2
R 3/83/8"16.6621.3371915.80614.9500.8560.18414.75
R 1/21/2"20.9551.8141419.79318.6311.1620.24918.25
R 3/43/4"26.4411.8141425.27924.1171.1620.24923.75
R 11"33.2492.3091131.7730.2911.4790.31730
R 1 1/41 1/4"41.9102.3091140.43138.9521.4790.31738.5
R 1 1/21 1/2"47.8032.3091146.32444.8451.4790.31744.5
R 22"59.6142.3091158.13556.6561.4790.31756
R 2 1/22 1/2"75.1842.3091173.70572.2261.4790.31771
R 33"87.8842.3091186.40584.9261.4790.31785.5
R 44"113.0302.30911111.551110.0721.4790.317110.5
R 55"138.4302.30911136.951135.4721.4790.317136
R 66"163.8302.30911162.351160.8721.4790.317161.5
说明:补充资料仅用于学习参考,请勿用于其它任何用途。