说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 紧凑拉伸剪切
1)  compact tension shear
紧凑拉伸剪切
1.
In this article,the photoelasticity is tested by using compact tension shear specimen.
本文采用紧凑拉伸剪切试样作了光弹性测定。
2)  compact tension
紧凑拉伸
1.
The results showed that the KIC of the compact tension specimens of L-R orientation was evidently higher than that of the compact tension specimens of R-L orientation and C-R orientation.
结果表明:L-R取向的紧凑拉伸试样的KIC明显高于R-L取向和C-R取向。
3)  compact shear
紧凑剪切
1.
The shear fracture behavior of cracked specimens was studied by the compact shear fracture test and finite element numerical simulation for Titanium alloy TC4 and PMMA.
利用紧凑剪切断裂试验和有限元方法数值模拟对TC4(Ti6A14V)钛合金及PMMA 有机玻璃Ⅱ型断裂行为进行了研究试,验结果表明:存在两种完全不同的断裂模式,(a)裂 纹起裂方向以相对于原裂纹面70°~83°扩展为特征的断裂形态,简称拉伸型扩展。
4)  single lap shear
拉伸剪切
5)  cut pull
剪切拉伸
6)  compact tension specimen
紧凑拉伸试样
1.
Studies on loading-point displacement for compact tension specimens
紧凑拉伸试样加载点位移研究
2.
To study the performance of SiC/Al Functionally Gradient Material(FGM),the numerical simulation analysis on the creep performance of three-point bending and compact tension specimen of SiC/Al FGM with four gradient layers is done under the thermal load and mechanical load coupling with thermal load by using ANSYS.
为研究SiC/Al梯度功能材料(Functionally Gradient Material,FGM)的性能,采用ANSYS分别对具有4个梯度层的该种材料的3点弯曲试样和紧凑拉伸试样,在热载荷和机械载荷热载荷共同作用下的蠕变性能进行数值模拟分析,得到不带微裂纹、带垂直梯度方向微裂纹和平行梯度方向微裂纹的SiC/AlFGM试样在这两种工况下的蠕变应变随坐标位置及时间变化曲线。
补充资料:拉伸剪切粘接强度
分子式:
CAS号:

性质:对粘接头试片的胶层施加拉伸剪切负荷,至接头破坏的最大负荷,除以粘接面积的值。也即在平行于胶层的载荷作用下,胶接试样破坏时,单位胶接面所承受的剪切力,用MPa表示。胶黏剂的拉伸剪切强度试验还常在高温或低温条件下进行。是胶黏剂主要的胶接强度指标,许多国家都有标准试验方法。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条