1) minute solid particle diameter
固体微粒粒径
1.
A photoelectric detection method with the use of an optical fibre probe can be employed to measure the minute solid particle concentration and velocity in gas-solid dual phase flows, but both the construction of the optical fibre and the variation of the minute solid particle diameter may significantly affect the result of measurement and calculation.
用光纤做探头的光电检测法可用于气－固两相流中固体微粒浓度、速度的测量，但光纤探头结构及被测固体微粒粒径的变化都会对测量、计算结果产生明显影响。
2) Solid particle
固体微粒
1.
The composition of solid particle and influence on interfacial tension between organic phase and water phase were investigated at different pH by using XRD and interfacial tension instrument.
为查清紫金山铜矿溶剂萃取铜过程界面乳化的原因,采用X射线衍射和界面张力等现代分析检测手段,考察了铜溶剂萃取过程中固体微粒的组成和来源以及不同pH值条件下不同种类的固体微粒对有机相-水相间界面张力的影响。
2.
The effects of solid particles on stability of interfacial emulsion in copper solvent extraction was studied.
对铜溶剂萃取时萃原液中固体微粒稳定界面乳化液的机理进行了研究。
3.
In order to investigate the influence of the solid particle on the zincous electrlbath's voltage and the quality and output of depositing zinc in zinc electrowinning,two different type of filters are introduced to carry out the filtration experiment of electrolysis mixture liquid.
指出悬浮在电解混合液中的固体微粒主要是钙和锶的不溶物、SiO2 及少量MnO2 。
3) solid particles
固体微粒
1.
For solid particles being the most deleterious matter in lubricating oils,the dielectrophoresis separation process system for removing the solid particles was established.
针对润滑油中危害最大物质之一的固体微粒,建立了润滑油介电动力学分离流态实验装置系统,研究了该方法主要工艺技术参数:电场强度和流速等。
2.
In order to avoid the formation of the third phase during the process of solvent extraction of copper,the composition of the solid particles in the third phase was examined by XRD as well as adsorption and degradation of the extractant caused by the solid particles were investigated by IR and GC-MS methods.
采用X射线衍射、傅立叶变换红外光谱、气-质联用色谱等分析检测手段研究了铜萃取过程中第三相固体微粒的组成、固体微粒对萃取剂的吸附和降解作用,寻求抑制铜萃取过程中第三相形成的方法。
4) particle size
微粒粒径
1.
The influences of process para meters,in terms of pressure,temperature,total flux and ratio of branch fluxes,on particle size is investigated at the same time.
结果表明,产物是纯度很高的锐钛型微粒,微粒粒径较小,粒度分布较集中。
2.
The influence of geometrical and material parameters on the scattering and absorption of electromagnetic wave is discussed numerically and he analysis for the different ratios of incident wavelengths to particle sizes are carried out in detail.
基于核壳双层结构球形微粒的电磁波散射与吸收理论,对空心核壳、实心核壳的电磁波散射、吸收特性进行分析,讨论了电磁波波长与微粒粒径不同比例下的核壳结构几何参数、物理参数对入射电磁波散射和吸收的影响。
3.
The analyses for the different ratios of incident wavelengths to particle sizes are carried out in detail.
基于球形双层核壳微粒的电磁波散射与吸收理论和离散偶极子近似方法,给出了离散偶极子近似方法的适用范围,并对空心核壳、实心核壳的电磁波散射、吸收特性进行了分析,讨论了电磁波波长与微粒粒径不同比例下微粒外壳的厚度、介电损耗对入射电磁波散射和吸收的影响。
5) solid lipid microparticles
固体脂质微颗粒
1.
Stabilizer distribution on surface of solid lipid microparticles and SLM stability: mesoscale simulation and experiments;
固体脂质微颗粒表面稳定剂的分布状况对其稳定性的影响:介观模拟与实验
2.
Solid lipid microparticles (SLM) are micro-size DDS made from lipids with high melting point as matrixes.
固体脂质微颗粒(Solid Lipid Microparticles, SLM)以熔点较高的脂质材料为载体,是生物相容性好、能有效控制药物释放的一种微尺寸药物传输系统。
6) solid lipid microparticle
固体脂微颗粒
1.
The emulsion-congealing method was adopted to prepare ibuprofen-loaded solid lipid microparticles(SLM) with tristearin as the carrier.
以硬脂精为载体材料,采用熔融-冷却法制备包载布洛芬的固体脂微颗粒(SLM),研究了不同稳定剂对SLM载药体系的稳定效果。
补充资料：调和平均粒径
分子式：
CAS号：
性质：在混合颗粒中，直径为d1、d2、…dn的颗粒的质量分率，分别为x1、x2、…xn，则混合颗粒的调和平均直径可按下式计算：
CAS号：
性质：在混合颗粒中，直径为d1、d2、…dn的颗粒的质量分率，分别为x1、x2、…xn，则混合颗粒的调和平均直径可按下式计算：
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条