1) single vector
单一矢量
1.
In this paper, a three-level DTC system is presented based on single vector selection table which resolves the problems of voltage unbalance of neutral point and high dv/dt of output voltage, typical in multilevel inverters.
提出一种三电平异步电动机直接转矩控制(DTC)系统,即基于单一矢量的控制算法。
2) unit vector
单位矢量
1.
A method of calculating angles of a cutting tool with unit vectors;
用单位矢量法求刀具角度
2.
This paper designed and trained a three-layer f ee dforward neural network to estimate the actual rotor flux and unit vector for d irect vector controlled induction motor speed drive.
针对直接矢量控制感应电机感应电机调速系统 ,设计和训练一个三层前馈神经网络以估计系统的实际转子磁链和单位矢量 ,并由此构成系统的闭环控制。
3.
The change rate of unit vector r 0,θ 0,β 0 of spherical and cylindrical coordinate is drawn with θ,β changing in the graphic directly and at the same time the operate procedure three dimensinal cableauon on the screen is listed.
直接配合图示给出球坐标中单位矢量r0 ,θ0 ,β0 (当然也包括柱坐标中的单位矢量r0 ,θ0 )随角度θ,β改变时的变化率 ,并同时给出在微机上成立体画面的操作程序 。
3) edge elements
矢量单元
1.
An improvement of the vector basis functions of quadratic hexahedral edge elements is presented.
改进了曲边六面体矢量单元的矢量基函数 。
4) uni-vector field
统一矢量场
5) integrating vector
矢量一体化
1.
The paper puts forward a global model oriented integrating vector processing, which uses super Spaghetti data structure with subtopological features to organize the vector spatial data, follows the industry standards implemented by integrating task to rebuild attitude source model and to build the topological information model composed of attitude parameters and spatial data with hidden to.
文中提出一种面向矢量一体化处理的全局模型,该模型采用具有亚拓扑特征的超Spaghetti数据结构进行矢量空间数据组织,并在此基础上面向一体化任务所执行的行业标准,进行属性资源模型重构,建立由具有隐含拓扑关系的空间数据和属性参数组成的拓扑信息模型,为实现具有智能化特征的一体化矢量数据处理过程奠定了完备的底层数据基础。
6) single vector model
单矢量模型
1.
The magnetization curves of single crystalline Si steel in different direction have been calculated using single vector model.
采用单矢量模型计算硅钢单晶不同方向的磁化曲线 ,给出了可以计算硅钢单晶任意方向磁化曲线的数值算法。
补充资料:伯格斯矢量
分子式:
CAS号:
性质:是位错尺寸的量度。当位错在晶体内滑动时,原子沿着某一特定的方向相对于其邻近原子切变了某一特定的距离,表示这种原子位移的矢量定义为位错的伯格斯矢量。对螺型位错,位错线平行于伯格斯矢量;对刃型位错,位错线垂直于伯格斯矢量;对于混合型位错,位错线斜交于伯格斯矢量。
CAS号:
性质:是位错尺寸的量度。当位错在晶体内滑动时,原子沿着某一特定的方向相对于其邻近原子切变了某一特定的距离,表示这种原子位移的矢量定义为位错的伯格斯矢量。对螺型位错,位错线平行于伯格斯矢量;对刃型位错,位错线垂直于伯格斯矢量;对于混合型位错,位错线斜交于伯格斯矢量。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条