说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 桥梁挠曲线
1)  Bridge deflection curve
桥梁挠曲线
2)  curved bridge
曲线梁桥
1.
In this paper the gridiron method is used to analyze 3 spans and 4 spans curved bridge which use same height web plate and different height web plate,and the better cross-section is chosen by each section’s index of steel and its stiffness.
文章应用梁格法,对等高腹板和不等高腹板两种截面形式的三跨、四跨曲线梁桥进行分析,以结构变形和钢材用量为主要指标比较两种截面形式的优缺点,进而给出两种截面形式的应用范围。
2.
Along with the development of transportation and civilization in our country, a lot of curved bridges have been widely applied in the high way and overpass.
随着我国交通事业的发展和城市化进程的加快,大量曲线梁桥运用于高速公路和城市立交桥中。
3)  curved bridges
曲线梁桥
1.
Analysis of the supports of curved bridges;
曲线梁桥的支座计算分析
2.
The proposed model is simple, yet it captures essential features that affect the dynamic response of curved bridges.
曲线梁桥的平面不规则性引起的弯扭耦合效应,导致了地震响应的复杂性。
4)  curve bridge
曲线桥梁
1.
Research purposes: Curve parallel arrangement method is a commonly used method for design of railway bridge,especially for the curve bridge crossing highway and river,but is generally used for small span bridge,so the research is done in this paper on application of this method in large span curve bridge for the purpose of enlarging the application scope of this method based on the example.
研究目的:曲线平行布置法是铁路桥梁设计,特别是在曲线桥梁跨越公路、河流的设计中经常采用的一种布置方法。
2.
Research purposes:For the peculiar crankle coupling mechanics peculiarity of the curve bridge that the structure internal force is quite intricacy.
研究目的:曲线桥梁由于具有独特的弯扭耦合力学特性,使得结构受力相当复杂。
5)  curved beam bridge
曲线梁桥
1.
This paper discussed the disease causes of the curved beam bridges.
曲线梁桥能够适应复杂的路况需要,是现代交通工程中的一种重要桥型。
2.
Based on the APDL programming technique,a fundamental procedure of developing a constructed prestressed concrete curved beam bridge simulation program is developed.
然后,重点讨论了基于ANSYS软件开发预应力混凝土曲线梁桥施工仿真程序中存在的一些问题。
3.
Two methods about how to calculate the bearing off-center of curved beam bridge are presented,which is common but no conclusion now.
根据恒载条件下横桥向双支座反力相等原则,对曲线梁桥设计中常见但尚无定论的支座偏心问题提出了2种计算方法,即最小偏心法和一致偏心法。
6)  curved bridge
曲线桥梁
1.
Spline function for plane line design of curved bridges;
曲线桥梁平面线形设计的样条函数法
2.
Theoretical research and earthquake damage investigation indicate that there is bend torsion coupling vibration for curved bridge when earthquake occurs.
理论研究与震害经验表明,地震时曲线桥梁会产生弯扭耦合振动。
补充资料:CAXA-V2线切割软件在DK7725e线切割机床上的应用
目前我国有大量的装有早期操作系统的数控设备,如何对其进行升级使这些设备重新焕发青春是摆在大家面前的一个很重要的问题。本文所介绍的正是这样的一个实例,文中所叙述的内容不仅对同类设备的改造具有现实意义,而且对其他类似设备的升级也有一定的借鉴作用。

    苏州三光的DK7725e线切割机床的操作系统是基于DOS平台上的,而CAXA-V2线切割软件是在Windows 98平台上开发的应用软件。显然,我们无法直接将CAXA-V2线切割软件安装到DK7725e线切割机床的操作系统中。解决这一问题的关键是寻找二者的共同之处,那就是机床的后置处理和传输功能单元,即G代码程序。


一、CAXA-V2线切割软件方面的操作


1.进入绘图界面


    在装有CAXA-V2线切割软件的计算机桌面上点击图标,进入该软件的绘图界面。


2.绘制零件图
   
    在软件的绘图区域中绘制线切割加工零件图,如图1所示。



图1 线切割加工零件


3.生成加工轨迹


    利用“轨迹生成”指令,生成线切割加工零件的加工轨迹,同时确定穿丝点位置和补偿量。


4.添加后置处理


    由于CAXA-V2线切割软件并未提供DK7725e线切割机床的“后置处理和传输”,需要手工添加,具体操作过程如下:


(1)点击CAXA-V2线切割软件的“后置处理和传输”图标,绘图区会弹出一个对话框。
(2)选中“增加机床”图标,在弹出的对话框中用键盘输入“BKDC”后,按确定键返回,如图2所示。
(3)在“后置处理和传输”的对话框中,按苏州三光的DK7725e线切割机床的“后置处理和传输”参数,手工输入相应的参数和指令,如图3所示。



图3 机床类型设置


(4)在“后置处理和传输”的对话框中点击“后置处理设置”后,相应地也会弹出一个对话框。该对话框中的参数要求也按苏州三光的DK7725e线切割机床的“后置处理设置”参数来设置,如图4所示。



图4 后置处理设置


5.生成G代码


    完成上述设置后,点击“代码生成”指令,选择“G代码生成”后,再选中线切割加工零件的加工轨迹,该轨迹图线将由绿色变为红色,最后点击鼠标右键,弹出记事本对话框显示相应的G代码加工程序,如图5所示。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条