说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 有效热压温度
1)  effective thermal press temperature
有效热压温度
1.
the concept of inihahve tharmal press temperatUre,effective thermal press temperature and the average highest temperature in the Plate.
本文分析了碾压砼路面板的胀缩过程,提出初始热压温度、有效热压温度概念和板平均最高温度。
2)  effective temperature
有效温度
1.
The result shows that its crystallite size is decreased,micro\|strain and effective temperature are increased as well as its crystalline lattice is disordered with grinding time increasing.
研究表明 :随着粉磨的进行 ,金红石型TiO2 的晶粒大小D减少、显微应变ε增加 ,有效温度系数增加 ,晶格无序化程度增强。
2.
Based on the indoor splitting fatigue test under wide temperature range and high stress level, this paper acquired the fatigue life and changing rule of the asphalt mixture, also addressed its adoption to the effective temperature of asphalt, which can be a reference to asphalt pavement structure design.
对一种常规级配的沥青混合料的疲劳性能进行了研究,通过较大温度范围、较高应力比的沥青混合料劈裂疲劳试验,得出了对应温度、应力比下沥青混合料的疲劳寿命及其变化规律,并探讨了其在沥青混合料有效温度方面的应用,以期为路面结构设计提供参考。
3.
The principle and structure of the self made testing instrument for measuring the effective temperature in the full cross section of steel rail are described and discussed in this paper.
论述了自行研制的钢轨全断面有效温度测试仪的原理及结构。
3)  operative temperature
有效温度
1.
Analyses selection of thermal comfort indexes, calculation on operative temperature and expression of thermal sensation.
对热舒适现场研究结果进行了总结,并对热舒适指标的选取、有效温度的计算、热感觉的表述方式等问题进行了讨论分析。
4)  hot-pressing temperature
热压温度
1.
Effect of hot-pressing temperature and natural curing time on properties of fast-curing cement particle board;
热压温度和养护时间对快速固化水泥刨花板性能的影响
2.
thickness and density of panels, hot-pressing temperature, etc.
采用常规热压法对刨花板板坯进行热压,探讨热压时中心层温度变化规律与板坯含水率、板厚、板材密度及热压温度等的关系,结果表明:在快速升温段、升温速度随板厚的增加而明显减小,随热压温度的提高而加快;在慢速升温段,升温速度随板厚的增大而显著加快,随热压温度的升高而明显加速,升温速度受目标密度和板坯含水率影响很小;板坯内水分蒸发所需时间随板厚、板坯含水率、热压温度、板材密度的增长而增加;板坯内水分蒸发温度随板材密度的增加而升高,随板厚的减少而升高,热压温度和板坯含水率对其几乎没有影响;加入胶粘剂会使快速升温段的升温速度有所加快,而使恒温段的水分蒸发温度有所降低。
3.
The relations between the rising velocity of temperature of mat\'s central-layer and moisture content of mats,density,hot-pressing temperature,thickness were analyzed.
【目的】研究板坯含水率、目标密度、热压温度及板材厚度4个因素对棉秆重组材板坯中心层升温的影响,为制定棉秆重组材的热压工艺提供参考。
5)  temperature [英]['temprətʃə(r)]  [美]['tɛmprətʃɚ]
热压温度
1.
This paper introduces the physical and chemical change of particleboard in the course of hot pressing and analyses the effect of temperature,heating time and pressure.
介绍了刨花板热压过程中板坯的物理变化和化学变化,分析了热压温度、时间、压力在热压过程中的作用,阐明了热压工艺是刨花板生产中产品质量保证的重要环节。
2.
Through the practicing wo rk get every technology parameter such as temperature pressure and time for the hot press.
研究了影响二次贴面的生产工艺,通过实践制定热压温度、压力、时间等各项工艺参数。
6)  hot pressing temperature
热压温度
1.
Effect of hot pressing temperature on the microstructure and properties of C-SiC-B_4C composite;
热压温度对C-SiC-B_4C复合材料性能的影响
补充资料:有效温度
      发射出与某恒星数量相同的总辐射流,而又具有与该恒星半径相同的绝对黑体所具有的温度;也就是把恒星当作一个球形的绝对黑体,按照绝对黑体总辐射流和温度的关系,由恒星总辐射流 所确定的温度 Te就称为该恒星的有效温度。L为恒星总光度,R为恒星半径,σ 为斯忒藩-玻耳兹曼常数。太阳的有效温度测定得最精确。实测得到的太阳有效温度 Te=5,770±10K。绝大多数恒星的有效温度不能直接测定。其原因是:①离我们太远,它们的半径难以精确测定;②对于角直径已经测定的恒星,由于地球大气对紫外辐射的强烈吸收,不能准确地测定它们(特别是紫外辐射较强的早型星)在整个波长区域的总辐射流。因而只能用间接的方法,如恒星连续光谱的能量分布、热改正等方法,来确定恒星的有效温度。
  
  知道一颗恒星的有效温度,就可以估算它的总辐射流,推断它的光谱特征。恒星的光谱型与有效温度有密切关系,如:O5型恒星的有效温度Te≈40,000K,G5型恒星的Te≈5,520K,而M8型恒星的Te≈2,400K。由太阳的有效温度为5,770K,可知它是一颗G2V型恒星,而太阳的光谱特征也证明它是一颗G2V型恒星(见恒星光谱分类)。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条