1) fiber yield
纤维产量
1.
The fiber yield and qualities of 10 introduced flax varieties in Yunnan province,China;
10个引进亚麻品种在云南的纤维产量和品质分析
2.
The Characters of Ca on Ramie(Boehmeria Nivea L.)and Effects on Fiber Yield and Quality of Ramie;
苎麻钙素营养特征及其对纤维产量、品质的影响
3.
The research results of effects of different sowing date on kenaf fiber yield and main agronomic characters in Xinyang area showed that May 5 is the best sowing date.
信阳市红麻不同播期的纤维产量及主要农艺性状的研究结果表明,该区的红麻最适播种期是5月5日。
2) Fibre yield
纤维产量
1.
A correlation and path-coefficient analysis was conducted of the components of flax fibre yield and the results showed that the mono-correlation coefficients of the fibre yield with the straw yield, the retting stem ratio and the fiber ratio were uncertain; but all the partial correlation coefficients were positively correlated.
分析结果表明，原茎产量、干茎制成率和出麻率与纤维产量的单相关系数是不确定的，但是偏相关系数均为正相关，而且原茎产量、出麻率与纤维产量均为极显著正相关。
3) Cellulase yidle
纤维素酶产量
4) fiber production
纤维生产
1.
Diphyl application in fiber production;
Diphyl在纤维生产中的应用
2.
The new machinery and accessories for fiber production, form polymer production to fiber process, showed in the ITMA 2003 are indroduced.
介绍了ITMA 2 0 0 3上展示的用于纤维生产的新型设备及其附件 ,涉及从聚合物合成到纤维后加工全过程。
5) fiber content
纤维掺量
1.
The variation between fiber content and compressive strength,splitting strength were analyzed.
为了研究纤维掺量对沥青混凝土强度的影响,选用5种纤维掺量沥青混凝土的马歇尔试件和圆柱体试件,在MTS810材料试验机上进行劈裂试验和单轴压缩试验,分析了劈裂试验结果和抗压强度随纤维掺量变化的规律。
2.
When the base strength grade is in the range of C30~C50,and thread steel fiber content is 0~1.
5%掺量范围内,对抗压强度的增强作用明显;当基体强度等级达到C60,纤维掺量在0。
3.
The viscoelastic performance was simulated by using four-unit five-parameter model,its parameters were obtained from the data of the test,and a four-unit five-parameter viscoelastic constitutive model with fiber content was set up.
根据粘弹性力学理论,采用"四单元五参数"模型(修正的Bugers模型)模拟纤维沥青混凝土的粘弹性能,其参数值由试验数据的数值拟合获得,提出了计入纤维掺量的"四单元五参数"粘弹性本构模型。
6) Fiber content
纤维含量
1.
The influence of the short fiber content,fiber length and hybrid effect on the tensile,flexual and impact properties are mainly discussed.
本文讨论了模压成型制成的短纤维增强PVC的制备方法和力学性能,主要探讨了纤维含量、纤维长度、混杂纤维效应等对复合材料拉伸、弯曲和冲击性能的影响。
2.
The tensile strength, flexural and impact strength of samples with different fiber contents are investigated by comparing three kinds of composites with fiber contents of 10,20 and 30wt%.
将纤维重量含量分别为 10 %、2 0 %和 30 %的复合材料进行比较 ,分析纤维含量对复合材料拉伸、弯曲和冲击性能的影响 ;将纤维分别切成约 3mm、5mm和 10mm长制成复合材料进行比较 ,分析纤维长度对复合材料拉伸、弯曲和冲击性能的影响。
3.
Wearability of composites with different fiber orientation and different fiber content has been analyzed.
着重研究了纤维取向、纤维含量、外加载荷的变化对复合材料磨损性能的影响、通过对磨痕扫描电镜的观察，探讨了复合材料的磨损机理。
补充资料：碳(石墨)纤维增强体(见碳纤维、石墨纤维)
碳(石墨)纤维增强体(见碳纤维、石墨纤维)
earbon(graPhite)fibrereinforeements
，、、里z耽维增强体earbon(graphi现inforcements用于复合材料中承受负荷，田的磷纤始知五史纤俯亡e)fibre起增强作
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条