说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 齿厚偏差
1)  deviation of width of teeth
齿厚偏差
1.
After inputting the precision rank and symbol of deviation of width of teeth of internal gear pair,the biggest center distance after reducing width of teeth can be determined.
提出了考虑K H V型渐开线少齿差行星减速器在三种不同的中心距 ;理论中心距、齿厚减薄后最大中心距和试验中心距下的工作情况 ;通过输入齿轮精度等级和齿厚偏差代号确定齿厚减薄后最大中心距 ,并试输入小于齿厚减薄后最大中心距的试验中心距确定中心距的最大偏差范围 ,为制订最经济的中心距公差提供依据 ,并开发了仿真系统软件进行验证。
2)  tooth thickness allowance
齿厚允许偏差
1.
This paper introduces a method and some corresponding software for calculating tooth thickness allowance in involute cylindrical gears,based on ISO1328 1990 s International Standards for Gear Accuracy.
介绍了基于ISO1328九十年代国际齿轮精度标准的渐开线圆柱齿轮齿厚允许偏差的计算方法和为此编制的电脑软件,该方法对推动齿轮新老标准的转换具有较高的实用价值,可供生产、经销和使用齿轮的企业参考或选用。
3)  tooth thickmess error
齿厚误差
4)  thickness deviation
厚度偏差
1.
The effect of thickness deviation on the reflection spectra and phase shift of VCSELs has been analysed using optical transfer matrix method.
采用光学传输矩阵方法分析了厚度偏差对VCSEL的反射谱和反射相移产生的影响。
2.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill,rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a variety of roll length,plate width and rolling force is studied too.
针对由于轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析了轧辊承受载荷的分布情况,研究了宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
3.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill, rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a varity of roll length, plate width and rolling force is studied too.
针对轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析轧辊承受载荷的分布情况,研究宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
5)  Wall thickness deviation
壁厚偏差
6)  thickness deviation
板厚偏差
1.
Through analyzing the demand of thickness deviation, a new monitoring method basing on ultrasonic measurement technique and computer control technique was put forwared.
基于板厚偏差在线监测这一问题展开研究,采用智能仪器的设计方法和手段,进行人造板厚度在线监测系统的研究设计。
补充资料:齿(齿所)

齿(齿所)

齿(齿所)   病名。系指牙齿被醋浸渍的病证。《诸病源候论》卷二十九:“齿(齿所),齿伤酢也。齿者骨之所终,髓之所养,髓弱骨虚,风气客之,则齿(齿所)。”酢,同醋。参见齿齼条。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条